Aluminium Adhesive Heatsink pack 3pcs

Descripción:
Chip XL4015 - Upgrade of the LM2596
Drop module
Use a multimeter to check the output voltage and adjust the potentiometer
Voltage control
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:
- Input voltage: 4.5V-38V
- Output voltage: 1.25-36.5V
- Current output: 4.5A (max 5A)
- Output power: 75W maximum
- Operating temperature: -40 to + 85 ºC
- Operating frequency: 180KHz
- Efficiency conversion: up to 96%
- Short circuit protection: Yes (limited current 8A)
- Protection over temperature: the output switches off automatically
- Size: 62mm x 38mm x 15mm
Principal functions:
- Step-down converter with overcurrent protection
- Li-Po battery charger, Li-Ion

Resistors 470R Ohm 5% 0,25W 1/4W features:
- 470R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Dupont female-female connector cable to PH2.00 for Nema engine features:
Dupont 2.54 female to PH2.00 female connecting cable for Nema motor Length 100cm

10x Long 6-Pin Female Strip features:
- Pin spacing: 2.54 mm
- Pin length: 10.5 mm
- Insertion position: Vertical
- Insertion: Through
- Quantity: 10 units of female strips of 6 pins each

Bowden connector - a pneumatic connector with a 6 mm screw and 1.75 cm length for the 4mm tube of 3D printer couplers for 1.75 mm filament. 

M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer features:
- This sensor can be configured as Z axis auto level
- Inductive proximity sensor detection switch LJ12A3-4-Z / BX
- NPN DC6-36V
- Often used for 3D printer bed leveling
- Typical application: 3D printer bed level sensor
- Type of Cylindrical DC cable 3 type of cable (black, brown, blue)
- Inductive sensor type
- NPN NO (Normal Open)
- Detecting Distance 4mm
- DC supply voltage 6-36V
- 300mA current output
- 0.5KHz response frequency
- Detects iron / aluminum
- Operating temperature -25 ° C to + 55 ° C (Condition non-freezing)
- Head diameter 12 mm
- Size 6.2 x 2cm
- Cable length 100cm

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

Characteristic: - Supports up to 280ºC
- Electrical and antistatic insulation
- Resistant to acid and alkaline products
- Resistant to solvent
- Adhesive
- Length Approx: 33m
- Polyamide adhesive tape 10mm 
- Known as Kapton polyamide tape
- Product for welding works on those that need to protect some component from the heat