Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.99
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €2.29
PCA9685 digital servo motor controller 16 channel PWM This module can handle 16 PWM signals, through an I2C connection with devices like microcontrollers or development boards like Arduinos. It can also be concatenated with other equal modules (up to 62 cards), increasing versatility and allowing you to obtain up to 992 PWM outputs that can be used to connect servo motors or LEDs to change the brightness intensity. PCA9685 digital servo motor controller 16 channel PWM features: - Supply voltage: 3-5 VDC, - Maximum motor voltage: 6 VDC, - Number of channels: 16, - Resolution per channel: 12 bits, - Interface: I2C, - Working frequencies: 40-1000 Hz, - PCB size: 62.3x25.3mm . Code R0074 Available Price €5.10
Flux Welding Paste 20g Characteristic: - Solder paste according to DIN EN 29454-1 1.1.2.C. - Flux paste based on activity rosin medium. - Easy to weld: copper, silver, zinc and nickel plated. Flux residues after soldering do not cause corrosion of non-ferrous metals and can remain in the joints . Operating temperature up to 350 C. Code Q0025 Available Price €1.89
Relay Module DC 5V 10A 2 Channel Low/High Trigger Relay Module DC 5V 10A 2 Channel Low/High Trigger features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- It has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL002 Available Price €3.15
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.95
1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino 1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL001 Last items in stock Price €2.39
Tower Pro Micro Servo 9g SG90 360 degree Tower Pro Micro Servo 9g SG90 360 degree features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0075 Available Price €2.95
Kit 2x Blue Aluminium and Gold flat metal heatsinks For Raspberry Pi 2 and Pi 3, B and B +. Each heatsink includes thermal sticker. Kit 2x Blue Aluminium and Gold flat metal heatsinks features: 1 blue aluminum heatsink: - Dimensions: 9x9x12mm 1 flat metal sink gold color: - Dimensions: 12x12x1mm Code RA022 Available Price €1.49
Pimoroni Fan SHIM Pimoroni Fan is the best you can do for your new Raspberry 4! It is a well known fact, Raspberries can get hot. Even though, there are plenty of solutions to that, you will find no better than this Pimoroni Fan. It is a no-solder device, hence you can put it on and off as you wish Code PI009 Available Price €15.99
Retroflag NESPi Case for RetroPie Raspberry PI with 2x Super SNES Controller This set will make your project look like take out of 80s! Box and two controllers imitate a game console only for 25 EUR. Do you miss old times of Nintendo? You won´t anymore with this great set. It is perfect for a gift as well. Check out product characteristics for further information Code RA052 ✗ Out-of-Stock Price €25.99
Kit 2x Adhesive Dissipaters of Covers and Blue Aluminium For Raspberry Pi 2 and Pi 3, B and B +. Each heatsink includes thermal sticker. Characteristic: 1 cover sink: - Dimensions: 13x12x5mm 1 blue aluminum sink: - Dimensions: 9x9x12mm Code RA021 Available Price €2.49
Grey Flat Cable GPIO 40 Pins M/F Raspberry Pi (RPi2, RPi3, B and B+) Grey Flat Cable GPIO 40 Pins M/F Raspberry Pi (RPi2, RPi3, B and B+) features: -Length: 25cm -Quantity: 1 unit -Female connectors at both ends -High quality and good working condition -easy to install and use Code RA008 Available Price €2.95
Flat Cable GPIO 40 Pins M/F Flat Cable GPIO 40 Pins M/F features: - For Raspberry Pi 2 and Pi 3, B and B + - Total length 20cm - Quantity: 1 unit Code RA007 Available Price €2.85
Ethernet Patchcord UTP 5e 2m Ethernet Patchcord UTP 5e 2m features: Code K0273 Available Price €2.59
Transparent housing for Raspberry Pi 2, Pi3 Model B, B+ Transparent housing for Raspberry Pi 2, Pi3 Model B, B+ features: - Case Case Shell Box - Housing for Raspberry Pi 2 and Pi 3, B and B + - Transparent color - Made of ABS - Dimension: 95x 62x 26mm Code RA003 Available Price €2.70
Pibow Zero Case for Raspberry Pi Zero version 1.3 This colourful protective case or cover is for the Raspberry Pi Zero v1.3 only. This case is not compatible with the Pi Zero W or the Pi Zero v1.2 (without camera connector) It does not include a Raspberry Pi Zero v1.3! Code PI010 Available Price €5.90
Pibow Coupé 4 - Ninja - Case for Raspberry Pi 4 The Pibow Coupé 4 is the ideal slim, hackable and attractive case for your Raspberry Pi 4. Code PI013 Available Price €9.95
Kit 2x Blue Aluminium and Gold flat metal heatsinks For Raspberry Pi 2 and Pi 3, B and B +. Each heatsink includes thermal sticker. Kit 2x Blue Aluminium and Gold flat metal heatsinks features: 1 blue aluminum heatsink: - Dimensions: 9x9x12mm 1 flat metal sink gold color: - Dimensions: 12x12x1mm Code RA022 Available Price €1.49
Pimoroni Fan SHIM Pimoroni Fan is the best you can do for your new Raspberry 4! It is a well known fact, Raspberries can get hot. Even though, there are plenty of solutions to that, you will find no better than this Pimoroni Fan. It is a no-solder device, hence you can put it on and off as you wish Code PI009 Available Price €15.99
Retroflag NESPi Case for RetroPie Raspberry PI with 2x Super SNES Controller This set will make your project look like take out of 80s! Box and two controllers imitate a game console only for 25 EUR. Do you miss old times of Nintendo? You won´t anymore with this great set. It is perfect for a gift as well. Check out product characteristics for further information Code RA052 ✗ Out-of-Stock Price €25.99
Kit 2x Adhesive Dissipaters of Covers and Blue Aluminium For Raspberry Pi 2 and Pi 3, B and B +. Each heatsink includes thermal sticker. Characteristic: 1 cover sink: - Dimensions: 13x12x5mm 1 blue aluminum sink: - Dimensions: 9x9x12mm Code RA021 Available Price €2.49
Grey Flat Cable GPIO 40 Pins M/F Raspberry Pi (RPi2, RPi3, B and B+) Grey Flat Cable GPIO 40 Pins M/F Raspberry Pi (RPi2, RPi3, B and B+) features: -Length: 25cm -Quantity: 1 unit -Female connectors at both ends -High quality and good working condition -easy to install and use Code RA008 Available Price €2.95
Flat Cable GPIO 40 Pins M/F Flat Cable GPIO 40 Pins M/F features: - For Raspberry Pi 2 and Pi 3, B and B + - Total length 20cm - Quantity: 1 unit Code RA007 Available Price €2.85
Ethernet Patchcord UTP 5e 2m Ethernet Patchcord UTP 5e 2m features: Code K0273 Available Price €2.59
Transparent housing for Raspberry Pi 2, Pi3 Model B, B+ Transparent housing for Raspberry Pi 2, Pi3 Model B, B+ features: - Case Case Shell Box - Housing for Raspberry Pi 2 and Pi 3, B and B + - Transparent color - Made of ABS - Dimension: 95x 62x 26mm Code RA003 Available Price €2.70
Pibow Zero Case for Raspberry Pi Zero version 1.3 This colourful protective case or cover is for the Raspberry Pi Zero v1.3 only. This case is not compatible with the Pi Zero W or the Pi Zero v1.2 (without camera connector) It does not include a Raspberry Pi Zero v1.3! Code PI010 Available Price €5.90
Pibow Coupé 4 - Ninja - Case for Raspberry Pi 4 The Pibow Coupé 4 is the ideal slim, hackable and attractive case for your Raspberry Pi 4. Code PI013 Available Price €9.95