40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.99
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.99
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €5.39
Matrix Membrane Keyboard 4x4 Modulo High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side. Ideal for your Arduino projects, but can also be used with other microcontrollers. Matrix Membrane Keyboard 4x4 Modulo features: - Rating circuit, Max: DC 35V 100 mA - Cable length: 85 mm - Dupont 8 pin connector - Specific insulation: 100 M Ohm, 100V - Useful life: + 1 million uses - Contact parting: Code M0025 Available Price €1.79
10m Rigid cable, 22AWG yellow PVC wire, 0.35mm2 Characteristic: -Conductor: solid wire, tinned copper -Insulation: PVC -Low voltage electrical cables - Nominal voltage 300V / 80C -Standard: UL 1007 -Number of conductors: 22AWG, 1x0.35mm2 -Outer diameter: 1.6mm Code K0226 Available Price €3.89
DS1302 Real Time Clock RTC Module AVR ARM PIC Ideal for projects with ARDUINO you can use it with PIC, AVR, STM32.Provides seconds, minutes, time and date, calendar up to the year 2100.DS1302 Real Time Clock RTC Module AVR ARM PIC features:- Chip: DS1302- Power supply: 2V-5V- Operating current: <2mA- Dimensions: 44 x23 x 8mm- Battery not included in this sale- Connect the RTC to your ArduinoVCC -> Arduino + 3.3VGND -> Arduino GndCLK -> (SCLK_PIN)DAT -> (IO_PIN)RST -> (CE_PIN) Code M0014 Available Price €1.96
SONOFF ZBBridge - Smart Zigbee Bridge - Obsolete The SONOFF ZigBee Bridge is the heart of the smart home that allows you to remotely manage a variety of ZigBee devices and sensors to monitor and control the home. Interact with all your Sonoff devices, both WiFi and ZigBee, thanks to this bridge. Code WS030
Flexible Coupler 6mm/10mm shaft High quality flexible aluminum coupler, so you can join Nema 17, 6mm stepper motors to a 10mm threaded rod. They incorporate 4 screws studs so you can perfectly fix the couplings to the rod. Flexible Coupler 6mm/10mm shaft features: - Material: Aluminum alloy - Coupler height (L ): 25 mm - Outside diameter: 19mm - Shaft diameter: 6mm / 10mm - Quantity 2units Code I0135 Available Regular price €1.99 -€0.50 Price €1.49
Raspberry Pi Pico GPIO Expansion Board The Raspberry Pi Pico GPIO Expansion Board is an advanced product with a 3.3V output voltage that allows you to easily work on the GPIO pins of your Pico, via two ways (male and female header). Ideal for using both male and female jumpers/bridge cables. Code RA125 Available Price €8.95
Raspberry Pi Pico Relay Board The Raspberry Pi Pico Relay Board allows you to control up to 4 devices and loads up to 240V AC at 7A, 30V DC at 10A. It provides a way for users to control high voltage/current devices. Code RA126 Available Price €24.95
Pimoroni Pico Explorer Base The Pico Explorer Base is an expansion board for the Raspberry Pi Pico, designed to teach circuit properties and allow you to perform science experiments, build small robots and inventions. The board includes functional components such as a mini prototyping board, motor drivers, ADC and GPIO cables, a speaker, a display with four usable buttons, switches and Breakout Garden rails for the expansion module. Code PI046 Last items in stock Price €32.49
Pimoroni Pico Scroll Pack - White The 17 x 7 rectangular matrix has a total of 119 white LEDs that can be controlled individually. A dedicated extension to the Raspberry Pi Pico. The device uses the 12C bus for communication and can be safely powered via the USB port. Code PI044 Last items in stock Price €21.49
Grove Shield for Raspberry Pi Pico v1.0 Grove Shield for Pi Pico v1.0 is a plug-and-play Shield for Raspberry Pi Pico that integrates with various types of Grove connectors, such as I2C, UART, digital and analog ports. It allows the construction of prototypes and projects in an easy and fast way without soldering or jumper wires, allowing to explore the infinite possibilities of the Pico. Code SS021 Available Price €7.90
Raspberry Pi Pico W with WIFI Following the hugely popular Raspberry Pi Pico, the new Raspberry Pi Pico W is a wireless version of the board based on the RP2040, which adds 2.4 GHz 802.11n WiFi connectivity. The chip has 26 GPIO pins that operate at 3.3V, as well as a built-in temperature sensor. The Raspberry Pi Pico is programmed in C/C++ and MicroPython, via a microUSB connector. Code RA151 Available Regular price €9.95 -€0.50 Price €9.45
Raspberry Pi Pico HAT Expansion Raspberry Pi Pico HAT Expansion is an input/output expansion board designed for Raspberry Pi Pico, which provides a set of 2x20 pin headers in the form of Raspberry Pi header along with a set of 2 x 20 pins. It allows any HAT designed for Raspberry Pi to be connected to Raspberry Pi Pico. Code RA130 Available Regular price €9.95 -€1.30 Price €8.65
Raspberry Pi Pico (With Soldered Header) The first Raspberry microcontroller with the proprietary RP2040 chip and a dual-core Arm Cortex-M0+, the Foundation's cost-effective yet highly flexible solution. Designed for high performance and with a high degree of digital interfaces. Programming in C/ C++ and MicroPython. Code RA131 ✗ Out-of-Stock Price €7.99
Raspberry Pi Pico (With Soldered Header) The first Raspberry microcontroller with the proprietary RP2040 chip and a dual-core Arm Cortex-M0+, the Foundation's cost-effective yet highly flexible solution. Designed for high performance and with a high degree of digital interfaces. Programming in C/ C++ and MicroPython. Code RA131 ✗ Out-of-Stock Price €7.99
Adafruit Feather RP2040 Adafruit's Feather meets Raspberry Pi's new RP2040 chip, offering this board with great features. This Feather features the RP2040 and all the niceties you know and love from Feather. It comes fully assembled and tested, with the UF2 USB bootloader. It also comes with a header, so you can solder it and connect it to a solderless test board. Code AD001 Available Price €11.90
Raspberry Pi Pico GPIO Expansion Board The Raspberry Pi Pico GPIO Expansion Board is an advanced product with a 3.3V output voltage that allows you to easily work on the GPIO pins of your Pico, via two ways (male and female header). Ideal for using both male and female jumpers/bridge cables. Code RA125 Available Price €8.95
Raspberry Pi Pico Relay Board The Raspberry Pi Pico Relay Board allows you to control up to 4 devices and loads up to 240V AC at 7A, 30V DC at 10A. It provides a way for users to control high voltage/current devices. Code RA126 Available Price €24.95
Pimoroni Pico Explorer Base The Pico Explorer Base is an expansion board for the Raspberry Pi Pico, designed to teach circuit properties and allow you to perform science experiments, build small robots and inventions. The board includes functional components such as a mini prototyping board, motor drivers, ADC and GPIO cables, a speaker, a display with four usable buttons, switches and Breakout Garden rails for the expansion module. Code PI046 Last items in stock Price €32.49
Pimoroni Pico Scroll Pack - White The 17 x 7 rectangular matrix has a total of 119 white LEDs that can be controlled individually. A dedicated extension to the Raspberry Pi Pico. The device uses the 12C bus for communication and can be safely powered via the USB port. Code PI044 Last items in stock Price €21.49
Grove Shield for Raspberry Pi Pico v1.0 Grove Shield for Pi Pico v1.0 is a plug-and-play Shield for Raspberry Pi Pico that integrates with various types of Grove connectors, such as I2C, UART, digital and analog ports. It allows the construction of prototypes and projects in an easy and fast way without soldering or jumper wires, allowing to explore the infinite possibilities of the Pico. Code SS021 Available Price €7.90
Raspberry Pi Pico W with WIFI Following the hugely popular Raspberry Pi Pico, the new Raspberry Pi Pico W is a wireless version of the board based on the RP2040, which adds 2.4 GHz 802.11n WiFi connectivity. The chip has 26 GPIO pins that operate at 3.3V, as well as a built-in temperature sensor. The Raspberry Pi Pico is programmed in C/C++ and MicroPython, via a microUSB connector. Code RA151 Available Regular price €9.95 -€0.50 Price €9.45
Raspberry Pi Pico HAT Expansion Raspberry Pi Pico HAT Expansion is an input/output expansion board designed for Raspberry Pi Pico, which provides a set of 2x20 pin headers in the form of Raspberry Pi header along with a set of 2 x 20 pins. It allows any HAT designed for Raspberry Pi to be connected to Raspberry Pi Pico. Code RA130 Available Regular price €9.95 -€1.30 Price €8.65
Raspberry Pi Pico (With Soldered Header) The first Raspberry microcontroller with the proprietary RP2040 chip and a dual-core Arm Cortex-M0+, the Foundation's cost-effective yet highly flexible solution. Designed for high performance and with a high degree of digital interfaces. Programming in C/ C++ and MicroPython. Code RA131 ✗ Out-of-Stock Price €7.99