Mini Submersible Water Pump DC 12V 200L/h 3W for ARDUINO Mini Submersible Water Pump DC 5.5-12V 200L / H 3W Mini Submersible Water Pump DC 12V 200L/h 3W ARDUINO features: * Operating voltage: 5.5-12V * Max flow: max. 200 l / h * Maximum pumping height: 40cm- max. 150cm * Cable length: 140cm * Jack DC 5.5x2.1mm connector (ext / int) * Outlet diameter: 8 mm * Dimensions: 36mm x 25mm Code M0111 Available Price €9.95
Mini Speaker 40mm Diameter 3W Impedance 4 Ohm MP3 Mini Speaker 40mm Diameter 3W Impedance 4 Ohm MP3 features: - Power 2-3W - Diameter: 40mm - Impedance: 4 Ohm - Quantity: 1 unit Code M0069 Available Price €1.95
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Last items in stock Price €5.90
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €4.49
Switch Button 8x8mm on-off Switch Button 8x8mm on-off features:- Switch terminals: Weldable- Measures: 8x8x13mm Code K0078 Available Price €0.22
Dupont Connector 2.54mm Female Dupont Connector 2.54mm Female features: - Connector for soldering or crimping - Lot 100 units - Ideal for your projects electronic, arduino, but can also be used with other microcontrollers Code K0110 Backorder Price €2.19
IR Remote Control + IR Infrared Receiver VS1838 IR Remote Control + IR Infrared Receiver VS1838 features: - The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal - Vcc supply: 3.3V-5V - IN digital output to connect to the port Arduino I / O - Remote measurements 85x 40x 5mm - Includes battery Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry: Send / Receive information via IR - Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module - Light a 3mm red LED by Infrared Code W0021 Available Price €2.49
Set of insulated connectors 175 units 18 types Insulated connectors set 175 pcs. 18 typesSet of insulated connectors 175 units 18 types features:Dimensions of the plastic box:- Width: 280 mm- Depth: 185 mm- Height: 42 mmTechnical data of the connectors:- Material: tinned steel- Insulation: PVC Code K0187 Available Price €9.99
ESP32-S3-DevKitC-1-N8R2 WROOM-1 WiFi + Bluetooth 5.0 ESP32-S3-DevKitC-1-N8R2 general-purpose development board based on the ESP32-S3R2-WROOM-1 chip, Flash 8MB, PSRAM 2MB. Code W0120 ✗ Out-of-Stock Price €26.59
Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: - Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU - Supply voltage: 5V - Logical levels: 3.3V - 16MB (128Mbit) flash - 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port - 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: of esp8266: - Supported protocols: 802.11 b / g / n - Network support: 2 , 4 GHz Code W0098 Available Price €10.90
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €7.49 -€1.29 Price €6.20
WiFi LoRa 32(V3) 863-928Mhz BLE5.0 OLED Classic development board designed and manufactured by Heltec Automation (TM), based on the ESP32-S3FN8 + SX1262. Integrates Wi-Fi, Bluetooth, lithium battery management system, dot matrix OLED screen, USB-C interface. Compatible with Arduino IDE, Micro Python, Platform.io, Espressif IDE. Our module is supplied with Lora antenna and IPEX adapter (U.FL) and header pins. Code W0128 Available Price €25.99
ESP32-S3-DevKitC-1-N8R8 WROOM-1 WiFi + Bluetooth 5.0 ESP32-S3-DevKitC-1-N8R8 general-purpose development board based on the ESP32-S3R8-WROOM-1 chip, Flash 8MB, PSRAM 8MB. Code W0121 ✗ Out-of-Stock Price €27.49
Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features: Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino / Code W0094 Available Price €9.95
Shelly 1 Shelly 1 is a universal smarthome relay enabled to work with all the key smart home systems, including Google Home and Amazon Alexa, as well as an original Shelly solution Shelly Cloud Code WH001 Available Regular price €15.95 -€1.50 Price €14.45
TUYA IoT Interface for controlling Arduino over WiFi TUYA IoT interface module - you will be able to control your projects IoT Internet of Things interface of your Arduino. Tuya interface that allows you to control outputs of the Arduino module via WiFi network using apps for Android and iOS mobile devices. The device communicates with Arduino via UART interface, powered by 5V. Code WT017 Last items in stock Price €18.90
SparkFun ESP8266 Thing - Dev Board (wo headers) ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes without headers. Code SP007 Last items in stock Price €25.99
Potentiometer B10K linear Characteristic: -10k OHM kΩ - linear potentiometer 10k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0067 Available Price €0.99
Micro Servo 9g SG90 Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0013 Available Regular price €2.69 -€0.20 Price €2.49
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.99
Resistor 220K Ohm 5% 0,25W 1/4W Resistor 220K Ohm 5% 0,25W 1/4W features:-220 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0027 Available Price €0.08
Prototype Board MB102 Protoboard 830 points for Arduino Prototype Board MB-102 Protoboard 830 points Arduino features: - 830 Connections - Linkable with other boards - Base with adhesive to attach it to the work surface - Measures 165x 55x8mm Code PB004 Available Regular price €2.99 -€0.50 Price €2.49
ESP32-S3-DevKitC-1-N8R2 WROOM-1 WiFi + Bluetooth 5.0 ESP32-S3-DevKitC-1-N8R2 general-purpose development board based on the ESP32-S3R2-WROOM-1 chip, Flash 8MB, PSRAM 2MB. Code W0120 ✗ Out-of-Stock Price €26.59
Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: - Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU - Supply voltage: 5V - Logical levels: 3.3V - 16MB (128Mbit) flash - 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port - 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: of esp8266: - Supported protocols: 802.11 b / g / n - Network support: 2 , 4 GHz Code W0098 Available Price €10.90
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €7.49 -€1.29 Price €6.20
WiFi LoRa 32(V3) 863-928Mhz BLE5.0 OLED Classic development board designed and manufactured by Heltec Automation (TM), based on the ESP32-S3FN8 + SX1262. Integrates Wi-Fi, Bluetooth, lithium battery management system, dot matrix OLED screen, USB-C interface. Compatible with Arduino IDE, Micro Python, Platform.io, Espressif IDE. Our module is supplied with Lora antenna and IPEX adapter (U.FL) and header pins. Code W0128 Available Price €25.99
ESP32-S3-DevKitC-1-N8R8 WROOM-1 WiFi + Bluetooth 5.0 ESP32-S3-DevKitC-1-N8R8 general-purpose development board based on the ESP32-S3R8-WROOM-1 chip, Flash 8MB, PSRAM 8MB. Code W0121 ✗ Out-of-Stock Price €27.49
Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features: Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino / Code W0094 Available Price €9.95
Shelly 1 Shelly 1 is a universal smarthome relay enabled to work with all the key smart home systems, including Google Home and Amazon Alexa, as well as an original Shelly solution Shelly Cloud Code WH001 Available Regular price €15.95 -€1.50 Price €14.45
TUYA IoT Interface for controlling Arduino over WiFi TUYA IoT interface module - you will be able to control your projects IoT Internet of Things interface of your Arduino. Tuya interface that allows you to control outputs of the Arduino module via WiFi network using apps for Android and iOS mobile devices. The device communicates with Arduino via UART interface, powered by 5V. Code WT017 Last items in stock Price €18.90
SparkFun ESP8266 Thing - Dev Board (wo headers) ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes without headers. Code SP007 Last items in stock Price €25.99