White Diode 9W LED COB SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone-coated tabletThe advantages of LED COB:- A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Opening angle of up to 160º Code P0029 Available Price €2.42
DC voltage sensor 0-25v for Arduino Voltage Sensor Module 0.02445V ~ 25V. When the module is powered by 5V voltage detection It does not exceed 25V, and when the module is powered with 3.3V the voltage detection does not exceed 16.5V. 100% Compatible with Arduino. DC voltage sensor 0-25v for Arduino features: - Input voltage: 0-25 VDC - Voltage detection range: 0.02445V-25 VDC - Analog voltage resolution: 0.00489 V - DC input connector: cathode terminal connected to VCC, GND negative pole - Output interface: "+" then 5 / 3.3V, "-" then GND, "s" then the Arduino AD pins Code M0191 ✗ Out-of-Stock Price €1.31
10m Rigid cable, 22AWG black PVC wire, 0.35mm2 Characteristic: -Conductor: solid wire, tinned copper -Insulation: PVC -Low voltage electrical cables - Nominal voltage 300V / 80C -Standard: UL 1007 -Number of conductors: 22AWG, 1x0.35mm2 -Outer diameter: 1.6mm Code K0224 Backorder Price €3.21
Support for HC-SR04 Ultrasonic Sensor Support for ultrasounds, HC-SR04 distance meter. Ideal to install the sensor on mobile platforms such as robots, vehicles, etc. Support for HC-SR04 Ultrasonic Sensor features: - Material: Acrylic - Color: transparent - Includes screws Code S0005 Available Regular price €1.20 -€0.50 Price €0.70
NEC IR Remote Control Infrared emitter HX1838 Arduino Raspberry Remote Control HX1838 Infrared Emitter NEC IR Remote Control Infrared emitter HX1838 features: - 21 keys - Measurements 85x 40x 5mm - Includes battery Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Send / Receive information via IR - Wiring of the IR Remote control + Infrared IR Receiver VS1838 with UNO module - Lighting a red 3mm LED by Infrared Realization of a manageable Infrared robot - Wiring the IR Distance remote control + Infrared IR Receiver VS1838 with the UNO module - Fix the IR Distance remote control + VS1838 Infrared IR Receiver in a Mini 2WD DIY Car Robot Kit Code W0020 Available Price €0.81
Logic Analyzer 8-Channel 24MHz USB SALEAE is an 8-channel logic analyzer without memory, a maximum sampling speed of 24MHz (depends on the PC and the use of the USB bus).It allows you to record and display digital data read on the computer.Logic Analyzer 8-Channel 24MHz features:- 8 channels- 24MHz sampling frequency- 1000M samples- USB power- USB 2.0 HiSpeed- 5V supply voltage- LED - power indicator- LED - logic indicator 0-1 on channel 1- USB connectionYou can change the sampling frequency by hand: 24MHz, 16MHz, 12MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500kHz, 250kHz, 200KHz, 100KHz, 50KHz, 25KHz.Works with TTL levels: low level from -0.5V to 0.8V and high level from 2V to 5.25V. Code K0080 Available Price €7.02
Construction kit 32 IN 1 micro:bit - Wonder Building kit With this 32 in 1 construction kit you can build all 32 options or develop your imagination by building your own project. Note: the micro:bit board is not included, you can buy it separately. Code EL0112 ✗ Out-of-Stock Regular price €78.47 -€5.00 Price €73.47
PLA Filament 1.75mm 1kg green interference colour Filament of PLA HD material, perfect for basic and fast projects that do not need excessive durability, for 3D printers. The diameter of the filament is 1.75mm. The package contains 1kg of green interference coloured filament Code I0737 Backorder Price €21.66
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Backorder Price €28.92
SparkFun IoT RedBoard - ESP32 Development Board SparkFun IoT RedBoard development board compatible with Arduino. It incorporates an ESP32 chip with a 32-bit dual-core Xtensa LX6 microprocessor with a clock frequency of up to 240 MHz. It enables WiFi and Bluetooth wireless communication, making it versatile for Smart Home and IoT projects. Code SP048 Last items in stock Price €37.60
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €3.71
ESP8266 ESP12E WiFi NodeMcu + Motor Drive L293D Expansion Shield Board Kit NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, Code W0016 Available Price €6.98
SparkFun ESP32 Thing The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right? Code SP009 Last items in stock Price €23.13
SenseCAP K1100 - Sensor kit with LoRa and AI - "SenseCAP K1100 - The Sensor Prototype Kit with LoRa® and AI allows you to quickly digitise your world with LoRaWAN® and solve real-world challenges. With this plug-and-play toolkit, anyone can add artificial intelligence to their edge devices and unlock the potential of AIoT. Code SS049 Backorder Price €65.28
Grove - Vision AI module, Himax HX6537-A processor, AI-powered OV2640 camera Grove - Vision AI module with Himax HX6537-A processor, thumb-sized AI-powered OV2640 camera sensor, compatible with YOLO v5 and Edge Impulse. Code SS051 Last items in stock Price €24.79
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €2.55
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 ✗ Out-of-Stock Price €7.81
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Regular price €3.93 -€1.00 Price €2.93
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €5.36 -€1.29 Price €4.07
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Backorder Price €28.92
SparkFun IoT RedBoard - ESP32 Development Board SparkFun IoT RedBoard development board compatible with Arduino. It incorporates an ESP32 chip with a 32-bit dual-core Xtensa LX6 microprocessor with a clock frequency of up to 240 MHz. It enables WiFi and Bluetooth wireless communication, making it versatile for Smart Home and IoT projects. Code SP048 Last items in stock Price €37.60
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €3.71
ESP8266 ESP12E WiFi NodeMcu + Motor Drive L293D Expansion Shield Board Kit NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, Code W0016 Available Price €6.98
SparkFun ESP32 Thing The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right? Code SP009 Last items in stock Price €23.13
SenseCAP K1100 - Sensor kit with LoRa and AI - "SenseCAP K1100 - The Sensor Prototype Kit with LoRa® and AI allows you to quickly digitise your world with LoRaWAN® and solve real-world challenges. With this plug-and-play toolkit, anyone can add artificial intelligence to their edge devices and unlock the potential of AIoT. Code SS049 Backorder Price €65.28
Grove - Vision AI module, Himax HX6537-A processor, AI-powered OV2640 camera Grove - Vision AI module with Himax HX6537-A processor, thumb-sized AI-powered OV2640 camera sensor, compatible with YOLO v5 and Edge Impulse. Code SS051 Last items in stock Price €24.79
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €2.55
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 ✗ Out-of-Stock Price €7.81
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Regular price €3.93 -€1.00 Price €2.93