40x Female-Female Cable 20cm 40x Female-Female Cable 20cm features: -Length: 20cm -Quantity: 40 wires -Dupont female connectors on both ends -Compatible with 2.54mm male connectors -High quality and good working condition -Easy to install and use Code K0004 Available Price €2.49
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €3.49
Motor Nema 17 1.22kg 17HS2408 Characteristic: - Motor passes 1.8º (200 steps per turn) - Capable of loading 1.22 kg / cm Code I0065 Available Price €8.99
Resistor 150R Ohm 5% 0,25W 1/4W Resistor 150R Ohm 5% 0,25W 1/4W features:-150R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0006 Available Price €0.08
DHT11 Temperature and Humidity Sensor The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features: - Operating voltage: 3 to 5 VDC- Humidity measurement range: 20-95% ± 5% accuracy- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy- Maximum sampling rate: 2 seconds- Working current 2.5mA- Iterfaz 1-wire- Dimensions: 2.3 x1.2x 0.5cm- Quantity: 1 unit Code S0010 Available Price €2.49
LCD TFT Display Module 128x160 1.8 SPI 1.8 TFT LCD screen with SPI interface and 5 control signals. Its touch screen is resistive, it has a resolution of 128x160 pixels.Easily programmable with UNO module, Arduino, Raspberry, Mega2560.LCD TFT Display Module 128x160 1.8 SPI features:- TFT LCD screen 1.8 128x160 pixels- Pixel: RGB vertical stripe- Driver ILI9163,- SPI interface: CS / MOSI / MISO / SCK (pins not soldered)- 5-pin interface CS, RS, SCL, SDA, RST for control- Resistive touch screen- Ideal for projects with ARDUINO, Uno R3, MEGA2560 Code P0135 Available Price €8.95
10x 8-Pin Long Female Strip 10x 8-Pin Long Female Strip features: - Pin spacing: 2.54mm - Pin length: 10.5mm - Insertion position: Vertical - Insertion: Through - Quantity: 10 units of 8-pin female strips each Code K0087 Available Price €0.19
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 ✗ Out-of-Stock Price €4.76
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €4.49
TUYA IoT Interface for controlling Arduino over WiFi TUYA IoT interface module - you will be able to control your projects IoT Internet of Things interface of your Arduino. Tuya interface that allows you to control outputs of the Arduino module via WiFi network using apps for Android and iOS mobile devices. The device communicates with Arduino via UART interface, powered by 5V. Code WT017 Last items in stock Price €18.90
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
ESP32-S3-DevKitC-1-N8R2 WROOM-1 WiFi + Bluetooth 5.0 ESP32-S3-DevKitC-1-N8R2 general-purpose development board based on the ESP32-S3R2-WROOM-1 chip, Flash 8MB, PSRAM 2MB. Code W0120 ✗ Out-of-Stock Price €26.59
SparkFun XBee Explorer Dongle SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables! The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA. Code SP038 Last items in stock Price €34.99
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €3.49
SparkFun ESP8266 Thing - Dev Board (with Headers) ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes with headers. Code SP008 Last items in stock Price €21.99
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 ✗ Out-of-Stock Price €4.76
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
ESP8266 ESP12E WiFi NodeMcu + Motor Drive L293D Expansion Shield Board Kit NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, Code W0016 Available Price €8.44
Shelly 1 Shelly 1 is a universal smarthome relay enabled to work with all the key smart home systems, including Google Home and Amazon Alexa, as well as an original Shelly solution Shelly Cloud Code WH001 Available Regular price €14.95 -€1.50 Price €13.45
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €3.49
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth, 4MB ESP32-WROOM-32E (ESP32-DEVKITC-32E) is an evaluation board with ESP32 processor, 4MB FLASH, 802.11 a/b/g/n (Wi-Fi, WiFi, WLAN) and BlueTooth® Smart Ready 4.x dual-mode. It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use. Code W0125 Last items in stock Price €13.95
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €9.49
Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0108 Available Price €8.99
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
ESP32 Breakout Board Shield GPIO 30PIN Useful adapter for 30-pin esp32 modules (2x15 pins). Provides easy and secure connections. You can use the terminal block sockets or create connections via female pin header. Code W0127 Available Price €4.49
ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0014 Available Price €4.95
ESP32-CAM WiFi Camera + Bluetooth Module The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot. Code W0100 Last items in stock Price €9.45
Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: - Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU - Supply voltage: 5V - Logical levels: 3.3V - 16MB (128Mbit) flash - 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port - 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features: of esp8266: - Supported protocols: 802.11 b / g / n - Network support: 2 , 4 GHz Code W0098 Available Price €10.90