2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino 2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL004 Available Regular price €3.15 -€0.50 Price €2.65
Male 40 Pin Header 1x40 Male 40 Pin Header 1x40 features: Type: Male, Insertion position: Vertical, Separation between pins: 2.54mm Code K0138 Available Price €0.69
TTL Converter Module 5V - 3.3V Bidirectional I2C Logic Level Connecting a 3.3V device to a 5V system is a challenge.The bidirectional logic level converter is a small device that safely drops the signals from 5V to 3.3V and increases 3.3V to 5V at the same time.This level converter also works with 2.8V and 1.8V devices. What really separates this logic level converter from our previous versions is that it can successfully set its high and low voltages and go up and down between them safely on the same channel.Each level converter has the ability to convert 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two sources of voltage (high voltage and low voltage) that your system is using. Code M0153 Available Regular price €4.99 -€2.00 Price €2.99
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.08
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €2.29
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Last items in stock Price €5.90
USBASP Atmega8 AVR Programmer Atmega128 Arduino compatible Adapter Cable Characteristic: - AVR 5V / 3.3V microcontrollers - change the programming voltage through jumper JP1 - LED status indicators - Transmission speed: 5kB / s - Fuse protector against possible damage to the USB port - Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux - Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦ - Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny15 € ¦ - CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦ - AT90S2313 series, AT90S2323, AT90S2343, AT90S4414, AT90S4433 € ¦ Code B0029 Available Price €6.59
3A DC Converter 4-53V Adjustable LM2596H Step Down Source Wide range of voltages, improved version. Drop module. They will use a multimeter to Check the output voltage and adjust the potentiometer. 3A DC Converter 4-53V Adjustable LM2596H Step Down Source features: - Based on the LM2596HVS-ADJ regulator - Rectification: Asynchronous - Output Voltage: 3v ~ 40v DC (adjustable) - Input Voltage: 4.5v - 53v DC - Max Output Current: 3A (with heat sink) - Ripple in output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5% - Operating temperature: -40ºC to + 85ºC - Measurements: 43x 21x 14 mm Code A0018 Available Price €2.79
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Available Price €11.89
NFC RFID Keychain Tag 13.56 MHz NFC RFID Keychain Tag 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with NFC Mifare 1k - Memory: 1kB EEPROM - Operating frequency: 13.56MHZ - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20ºC to 85ºC - Number of uses 100,000 times - Data retention: 10 years - Material: ABS - Dimensions 40.5 x 32 x 4.2 mm Code M0030 Available Price €0.99
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €9.99
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
NFC RFID round card 13.56 MHz Can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects 10x NFC RFID round card 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with Mifare S50 Classic - Memory: 1kB EEPROM - Operating frequency: 13.56MHz - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20 ºC to 85 ºC - Number of uses 100,000 times - Data retention: 5 years - Material: PVC - Dimensions: Ø 25 x 0.8 mm - Quantity: 10 units of NFC 13.56MHz card Code M0177 Available Price €0.49
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Available Price €11.89
NFC RFID Keychain Tag 13.56 MHz NFC RFID Keychain Tag 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with NFC Mifare 1k - Memory: 1kB EEPROM - Operating frequency: 13.56MHZ - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20ºC to 85ºC - Number of uses 100,000 times - Data retention: 10 years - Material: ABS - Dimensions 40.5 x 32 x 4.2 mm Code M0030 Available Price €0.99
NFC RFID round card 13.56 MHz Can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects 10x NFC RFID round card 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with Mifare S50 Classic - Memory: 1kB EEPROM - Operating frequency: 13.56MHz - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20 ºC to 85 ºC - Number of uses 100,000 times - Data retention: 5 years - Material: PVC - Dimensions: Ø 25 x 0.8 mm - Quantity: 10 units of NFC 13.56MHz card Code M0177 Available Price €0.49
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €9.99
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99