Resistor 100R Ohm 5% 0,25W 1/4W Resistors 100R Ohm 5% 0,25W 1/4W features:- 100R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0005 Available Price €0.08
DC voltage sensor 0-25v for Arduino Voltage Sensor Module 0.02445V ~ 25V. When the module is powered by 5V voltage detection It does not exceed 25V, and when the module is powered with 3.3V the voltage detection does not exceed 16.5V. 100% Compatible with Arduino. DC voltage sensor 0-25v for Arduino features: - Input voltage: 0-25 VDC - Voltage detection range: 0.02445V-25 VDC - Analog voltage resolution: 0.00489 V - DC input connector: cathode terminal connected to VCC, GND negative pole - Output interface: "+" then 5 / 3.3V, "-" then GND, "s" then the Arduino AD pins Code M0191 Available Price €1.59
4S BMS 25A 16.8V 18650 PCM PCB Circuit Charging Module In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0107 Available Price €4.59
LCD Display Screen 12864 128x64 Dots Graphic Blue Backlight Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. LCD Display Screen 12864 128x64 Dots Graphic Blue Backlight features:- Graphic LCD Screen 128x64 points- 5V power- Blue retro background illuminated, white letters- Controller ST7920- Parallel / serial communication- Dimensions PCB 93x70mm Code P0015 Available Price €9.95
16mm CGL camera lens, CSI-2 interface, resolution 10 megapixels 16mm fixed lens compatible with Raspberry Pi official HQ Camera (Reference RA094) C-mount, long distance telephoto type (up to 40m) 10 Mpx. Code RA132 Last items in stock Regular price €61.49 -€11.50 Price €49.99
HC-SR505 Mini Module Motion Detector Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 3 meters. One sensor electric pyro, which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. Characteristic: - Operating voltage: 4.5V- 20V - Consumption in idle state: Code S0037 Available Price €2.70
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Last items in stock Price €8.95
Micro SD Card Reader/Recorder The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.Ideal for projects with ARDUINO, PIC, AVR, STM32.Micro SD Card Reader/Recorder features:- Supply voltage: 4.5V- 5.5V- Adjustable 3.3V built-in regulator for SPI pins- Consumption <200mA- Interface: SPI- Dimensions: 24mmx 42mm x 12mmSupports microSD cards (up to 2G) and micro SDHC (up to 32G) Code M0006 Available Price €2.49
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Available Price €11.89
NFC RFID Keychain Tag 13.56 MHz NFC RFID Keychain Tag 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with NFC Mifare 1k - Memory: 1kB EEPROM - Operating frequency: 13.56MHZ - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20ºC to 85ºC - Number of uses 100,000 times - Data retention: 10 years - Material: ABS - Dimensions 40.5 x 32 x 4.2 mm Code M0030 Available Price €0.99
NFC RFID round card 13.56 MHz Can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects 10x NFC RFID round card 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with Mifare S50 Classic - Memory: 1kB EEPROM - Operating frequency: 13.56MHz - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20 ºC to 85 ºC - Number of uses 100,000 times - Data retention: 5 years - Material: PVC - Dimensions: Ø 25 x 0.8 mm - Quantity: 10 units of NFC 13.56MHz card Code M0177 Available Price €0.49
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €9.99
NFC RFID Keychain Tag 13.56 MHz NFC RFID Keychain Tag 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with NFC Mifare 1k - Memory: 1kB EEPROM - Operating frequency: 13.56MHZ - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20ºC to 85ºC - Number of uses 100,000 times - Data retention: 10 years - Material: ABS - Dimensions 40.5 x 32 x 4.2 mm Code M0030 Available Price €0.99
NFC RFID round card 13.56 MHz Can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects 10x NFC RFID round card 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with Mifare S50 Classic - Memory: 1kB EEPROM - Operating frequency: 13.56MHz - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20 ºC to 85 ºC - Number of uses 100,000 times - Data retention: 5 years - Material: PVC - Dimensions: Ø 25 x 0.8 mm - Quantity: 10 units of NFC 13.56MHz card Code M0177 Available Price €0.49
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Available Price €11.89
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €9.99