Sensor SCT-013-030, Non-Invasive 30A AC Current Meter The sensor measures the current flowing in the cable without cutting it. The measurement is made on a single insulated wire, the output is an analog voltage from 0 to 1 V. Sensor SCT-013-030, Non-Invasive 30A AC Current Meter features: Input current: 0 to 30A AC Output voltage: 0 to 1 V AC Built-in load resistance: 62 Ω Winding ratio: 1800: 1 Operating temperature range: -25 ° C to 70 ° C Cable length: 1 m Sensor weight: approximately 45 g Sensor SCT013-030 datasheet Code M0203 Available Price €6.49
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.08
Keyboard Shield 16x2 LCD screen for Arduino It is made up of a 16-character, 2-row, 6-button display. The display is compatible with the HD44780 controller and is connected in 4-bit mode so it can be used directly through the Arduino LiquidCrystal library. Ideal to navigate through the different parts of the configuration or map. Keyboard Shield 16x2 LCD screen for Arduino features: > - 2x16 LCD with blue backlight and white characters - Potentiometer to modify the LCD contrast - 5-push-button keyboard + RESET - Use of the minimum possible channels - Full compatibility with Arduino UNO and Mega - The display is compatible with the HD44780 controller - Response time: 30 ms - Size: 80 x 60 x 22 mm Code P0020 Available Price €4.49
Kit 37 Sensors in a Box for Arduino The perfect Arduino sensor kit to start learning about the world of electronics with Arduino. It comes with our step-by-step guide to each sensor, as well as its libraries. Code B0040 Available Price €19.49
Switch On/On 3-pin 6A SPDT This switch can be used for development projects and for the industry. All metal parts are not oxidized, the insulation material is of high quality.Its pins protected by an anti oxidant makes welding much easier. Switch On/On 3-pin 6A SPDT features: - Type: Latch SPDT- Material: Plastic, metal- Maximum operating current and voltage: 3A / 250V, 6A / 125V- Number of pins: 3- Pin size: 4.5x2 mm- Type of current: AC/DC- Pins to be welded- Switch action: 2 positions On/On- Size: 13.2x12.7x33.3mm Code K0420 Available Price €0.49
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €9.99
Mini Submersible Water Pump USB DC 5V 2-3L/Min 5V USB powered water pump. Submersible pump for aquariums. It doesn't make a lot of noise while you're working. Code M0219 Last items in stock Price €2.69
Ultrasound Distance Sensor HC-SR05 Ultrasonic sensors overcome many of the weaknesses of IR sensors by providing distance measurement regardless of the color and illumination of obstacles. Ultrasound Distance Sensor HC-SR05 features:- Power supply: 4.5-5.5 VDC - Supply current: 10 to 40 mA - Activation pin format: 10 μs digital pulse - Echo Pin Output: 0-Vcc - Echo Pin Format: the output is DIGITAL and directly proportional with range. See our conversion formula below - Measurement range: 2cm to ~ 4.5m - Measurement resolution: 0.3cm - Measurement angle: up to 15 degrees - Measurement speed: 40 Hz, - Connector: standard 5-pin male connector that can be connected directly to boards or breadboards: - 1: VCC - 2: Trig - 3: Echo Code S0047 Available Price €1.95
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €9.99
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Available Price €11.89
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.99
NFC RFID round card 13.56 MHz Can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects 10x NFC RFID round card 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with Mifare S50 Classic - Memory: 1kB EEPROM - Operating frequency: 13.56MHz - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20 ºC to 85 ºC - Number of uses 100,000 times - Data retention: 5 years - Material: PVC - Dimensions: Ø 25 x 0.8 mm - Quantity: 10 units of NFC 13.56MHz card Code M0177 Available Price €0.49
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €9.99
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Available Price €11.89
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.99
NFC RFID round card 13.56 MHz Can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects 10x NFC RFID round card 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with Mifare S50 Classic - Memory: 1kB EEPROM - Operating frequency: 13.56MHz - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20 ºC to 85 ºC - Number of uses 100,000 times - Data retention: 5 years - Material: PVC - Dimensions: Ø 25 x 0.8 mm - Quantity: 10 units of NFC 13.56MHz card Code M0177 Available Price €0.49