Dupont Connector 2.54mm Female Dupont Connector 2.54mm Female features: - Connector for soldering or crimping - Lot 100 units - Ideal for your projects electronic, arduino, but can also be used with other microcontrollers Code K0110 Backorder Price €1.81
Adapter SMA Female GPS GSM IPEX 2.4 Ghz RF ESP8266 1.13mm 50 Ohm Can be connected with the ESP8266 module with IPEXCompatible with Hirose U.FL and IPEX MHF1 Adapter SMA Female GPS GSM IPEX 2.4 Ghz RF ESP8266 1.13mm 50 Ohm features: - Frequency range: 0 ~ 6000MHz- Interface: SMA female connector- IPEX female connector- Cable length: 15cm- Coaxial cable: 1,13mm- V.S.W.R.: <1.5- Impedance (ohm): 50- Maximum input power (W): 50W- Operating temperature: -40ºC ~ + 70ºC Code W0071 Available Price €1.81
USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series An RS232 serial port to your PC through the USB port USB 2.0 A Serial Port Cable Adapter DB9 RS232 Series features: - CH341 driver- Supported OS: WinME, Win2003, Win XP, Vista, Win 7, Linux, MAC OS9.0/OSX- High quality, shielded cable- Power and data in the same cable, does not require more adapters- Compatible USB interface 1.1 and 2.0- Support up to 1 mega data transfer- Length 73cm The adapter allows you to connect a computer with: - Electric meters- Decoders, programmers- Cash registers- Satellite TV- Control panels- Mobile phones- Diagnostic interfaces for cars- The administration of Cisco routers Code C0010 Available Price €2.72
Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino compatible Limit Switch with Wheel - 5A 250 Vac - 1 switched - Arduino features: -Micro KW12-3 on / off switch -Max Current: 5A -AC voltage: 125-250V -Operating temperature: -40 to 70 degrees C -Quantity: 2 units Code K0018 Available Price €0.49
Printed Circuit Board Terminal 2 poles 5.08mm pitch Blue 2 pole PCB mount screw terminal 5.08mm pitch Printed Circuit Board Terminal 2 poles 5.08mm pitch features: Number of Contacts: 2 Pitch: 5.08mm Number of Rows: 1 Mounting Type: PCB Gender: Male Allowable Section: 1.5mm2 (22- 14 AWG) Termination method: screw Type: screw terminal block Nominal current: 16A Nominal voltage: 250V Color: blue Material: Nylon 66 Depth: 10mm Width: 7.5mm Length: 10mm Code K0217 Available Price €0.21
Digital Microscope U500X USB 2.0 Magnification 500 Digital microscope with 500x zoom, 8 LED lights and support for microscope included.Discover the emotion of a completely new microscopic world, totally hidden from the naked eye.This USB digital microscope can magnify objects up to 500 times its original size and uses a dynamic image sensor and eight super bright white LED lights to create detailed images.Connect the microscope to your computer via USB and admire each image on your screen.You can see details like skin pores, individual cotton threads, milky clouds or amber inside THC crystals or even small scratches in a collectable coin that would be impossible to detect with the naked eye, can be easily seen with this amazing USB digital microscope. Code H0131 Available Regular price €16.45 -€1.50 Price €14.95
Connectors 10x BLS05 Female/Female 5 Pins RoHS Single Row Connectors 10x BLS05 Female/Female 5 Pins RoHS Single Row features: - Step between pins: 2.54 mm- Manufacturer: Maritex- Number of connections: 5 in a single row- Type: female / female- RoHS standard Code K0121 Available Price €0.10
Dupont Connector 2.54mm Male Dupont Connector 2.54mm Male features: - Connector for soldering or crimping - Lot 100 units - Ideal for your projects electronic, arduino, but can also be used with other microcontrollers Code K0111 Available Price €1.81
NRF24L01 + Wireless Transceiver Module 2.4GHz It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features: - Based on chip NRF24L01 + Ultra Low Power- Free band: 2.4GHz ISM- Speed: 250kbps, 1Mbps, 2Mbps- Working current - reception: 13 mA- Transmission: 11 mA (900nA -deep sleep mode)- Receiving sensitivity: -94dB 250kbps- Coverage in closed spaces: 15m / 30m- SPI interface- Input voltage: 1.9V- 3.6V- Input / output port voltage: 0V-3.3V / 5V- Coverage in open areas: 100m approx.- Clock frequency: 16MHz Code W0005 Available Price €1.31
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 Available Price €4.12
Wireless communication module APC220 RF kit APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot. Code W0117 Available Price €37.93
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 ✗ Out-of-Stock Price €1.23
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €0.90
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €3.69
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €5.98
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.12
Wireless Transceiver Module with Antenna CC1101 This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.This is a significant improvement over the CC1100 module.It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @> Code W0083 Available Price €7.02
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.23
NRF24L01 + Wireless Transceiver Module 2.4GHz It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features: - Based on chip NRF24L01 + Ultra Low Power- Free band: 2.4GHz ISM- Speed: 250kbps, 1Mbps, 2Mbps- Working current - reception: 13 mA- Transmission: 11 mA (900nA -deep sleep mode)- Receiving sensitivity: -94dB 250kbps- Coverage in closed spaces: 15m / 30m- SPI interface- Input voltage: 1.9V- 3.6V- Input / output port voltage: 0V-3.3V / 5V- Coverage in open areas: 100m approx.- Clock frequency: 16MHz Code W0005 Available Price €1.31
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 Available Price €4.12
Wireless communication module APC220 RF kit APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot. Code W0117 Available Price €37.93
NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino compatible NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0065 ✗ Out-of-Stock Price €1.23
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €0.90
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €3.69
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €5.98
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.12
Wireless Transceiver Module with Antenna CC1101 This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.This is a significant improvement over the CC1100 module.It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @> Code W0083 Available Price €7.02
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.23