433MHz RF Wireless Receiver + Transmitter

- This module includes PA preamplifier and LNA (Low-noise amplifier)
- Comes with the SMA antenna for 2.4GHz (2dB)
- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer
- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features:
* Based on chip NRF24L01 +
* Free band: 2.4GHz ISM
* Speed: 250kbps, 1Mbps, 2Mbps
* Work current
- Reception: 45 mA
- Transmission: 115 mA (4.2uA -sleep mode)
* Receiving sensitivity:
-104dB 250kbps
- 95dB 1Mbps
- 92dB 2Mbps
* SPI interface

Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features:
- Transceiver based on the SI4432 Silicon Labs chip
- Ultrathin ultra small (16.5 × 17 mm)
- Good harmonics: easy for FCC / CE certification
- Penetration capacity (measured through 8 floors)
- Frequency range: 433.92MHz
- Sensitivity down to -121 dBm
- Maximum output power: 20dBm
- Data transfer rate: 0.123-256 kbps
- FSK, GFSK and OOK modulation
- Power supply: 1.8-3.6 V
- Ultra low power shutdown mode
- Digital indication of received signal strength (RSSI)
- Time to wake up
- Bidirectional antenna switch control and automatic adjustment
- Configurable packet structure
- Preamble detection

NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features:
- Operating voltage: 5V
- Wait time of the module receives the data: more than 2S
- The waiting time of the module sends data: more than 300
- Transfer speed: 50 Byte / S (theoretical value)
- I2C / TWI address: 0 x 47 (decimal 35)
- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)
- Size: 44 x 23 mm

This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.
The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.
This is a significant improvement over the CC1100 module.
It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.
Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @>

NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features:
- The NRF24L01 + module is powered with 3.3V
- This adapter module includes a 3.3V voltage regulator
- You can connect the NRF24L01 module on it at 5V voltage
- Dimensions of PCB: 25x 18mm
- Quantity: Adapter 1 unit

A compact, low-power Bottom Effect System Transceiver.
Transceiver based on the SI4463 Silicon Labs chip.
Industry standard model.
In full power operating conditions, open the communication distance up to 2000 km.
Much more than the SI4432.
Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver.
Higher sensitivity -126dBm.
The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation.
The data rate in the range of 100bps ~ 1Mbps.
Operating voltage of 1.8V ~ 3.6V.
FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features:
- Supply voltage: 1.8 ~ 3.6VDC

NRF24L01 Adapter + Wireless Transceiver 2.4GHz Socket Arduino features:
- The NRF24L01 + module is powered with 3.3V
- This adapter module includes a 3.3V voltage regulator
- You can connect the NRF24L01 module on it at 5V voltage
- Dimensions of PCB: 25x 18mm
- Quantity: Adapter 1 unit

Transceiver based on the SI4432 Silicon Labs chip
Industry standard model
Capacitive components manufactured by Murata with 10ppm high precision glass
Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:
- Supply voltage: 1.8 ~ 3.6VDC
(Note: a voltage higher than 3.6 V will cause permanent damage to the module)
- Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage)
- Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass)
- Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k)
- Transmission power: up to 20dBm (about 100mW)
- Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended)

It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features:
- Based on chip NRF24L01 + Ultra Low Power
- Free band: 2.4GHz ISM
- Speed: 250kbps, 1Mbps, 2Mbps
- Working current - reception: 13 mA
- Transmission: 11 mA (900nA -deep sleep mode)
- Receiving sensitivity: -94dB 250kbps
- Coverage in closed spaces: 15m / 30m
- SPI interface
- Input voltage: 1.9V- 3.6V
- Input / output port voltage: 0V-3.3V / 5V
- Coverage in open areas: 100m approx.
- Clock frequency: 16MHz