433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €0.90
10x Female-Male Cables 20cm Jumpers Dupont 10x Female-Male Cables 20cm Jumpers Dupont features: -Length: 20cm-Quantity: 10 cables-Connectors have male and female header contacts at either end-Compatible with male and female connectors 2,54mm-High quality and good working conditions-Easy to install and use Code K0009 Available Price €1.40
8A DC Step-down Converter 8-40V to 1.25-35V Current Control XL4016 A high-performance regulator-booster. 24V battery charger - DC / CV method. Power supply of the laptop from a 12V car battery. A high-performance dimmer-regulator. Charger for Li-Ion, Li-Po batteries etc. - CC / CV method. LED Constant current driver for LED diodes. Characteristic: - Input voltage: 6V -40V - Output voltage: 1.25-35V (adjustable) - Output current: 8A, (10A maximum) - Output power: 300W maximum - Efficiency of Conversion: up to 95% - Wiring: Solderless terminal - Operating frequency: 300kHz - Ambient temperature exceeds 40 ° C, increase heat dissipation - LED indicator two-color; - Charge red - Fully charged light green - No charge green Code A0011 ✗ Out-of-Stock Price €6.57
Resistor 100R Ohm 5% 0,25W 1/4W Resistors 100R Ohm 5% 0,25W 1/4W features:- 100R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0005 Available Price €0.07
LED 5mm RGB Cathode Commun LED 5mm RGB 4 Pins cathode commun with clear water lens. Code P0018 Available Price €0.17
Dupont Connector 2.54mm Female Dupont Connector 2.54mm Female features: - Connector for soldering or crimping - Lot 100 units - Ideal for your projects electronic, arduino, but can also be used with other microcontrollers Code K0110 Available Price €1.81
2x PCF8574P I/O Extension Board 8574 NXP - The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt. - Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)). - Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V. - Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs. - System Master can read from the input port or write to the output port through a single register. Code T0010 Available Price €0.95
SW-520D Vibration Metal Tilt Sensor Detects changes in the sensor angle and returns to the digital value. 5x SW-520D Vibration Metal Tilt Sensor features: - Contact resistance: Code S0020 Available Price €0.37
Pimoroni Pico Scroll Pack - White The 17 x 7 rectangular matrix has a total of 119 white LEDs that can be controlled individually. A dedicated extension to the Raspberry Pi Pico. The device uses the 12C bus for communication and can be safely powered via the USB port. Code PI044 Last items in stock Price €17.76
Expansion Board GPIO Shield 40 Raspberry Pi B+ Pin Expansion Board GPIO Shield 40 Raspberry Pi B+ Pin features: - Shield module for Raspberry Pi 2 and Pi 3, B and B + Code RA013 Available Price €5.66
Capacitive Fingerprint Scanner - UART (AD-013) - OBSOLETE This fingeprint scanner from ADH-Tech combines a highly precise fingerprint sensor module with an onboard MCU and UART interface enabling trivially very connection to any project. The scanner independently reads and analyses the fingerprint thanks to an MCU algorithm that can send a converted digital signal to a peripheral serial interface for a data read. The onboard MCU algorithm enables operations such as for example a fingerprint enroll. Code SP036
DS3231 Precision RTC Real Time Clock Module AVR ARM DS3231 Precision RTC Real Time Clock Module AVR ARM features: - Can be used in projects of Arduino, Raspberry Pi, PIC, AVR- Function compatible with the DS 3231- Power supply voltage: +2.3 V to +5.5 V- Temperature range: -40 ° C to + 85 ° C- Low energy consumption- Full clock calendar functions that include seconds, minutes, hours, date, month and year and valid until leap year compensation- Two alarm calendar- Interface: I2C Code RA011 Available Price €2.44
SparkFun Qwiic HAT for Raspberry Pi The Qwiic HAT is an absolute basic of Qwiic system for Raspberry. It enables a quick and efficient connection of an sensor to your Raspberry over I2C bus (GND, 3.3 V, SDA and SCL). As Qwiic enables daisy chaining of components, you can pretty much install as many sensors on the Qwiic HAT as you want. On top of that it fits perfectly Pi Tin enclosure from SparkFun enabling connection while in case. Code SP031 Available Price €6.60
SparkFun MEMS Microphone Breakout - INMP401 (ADMP401) - obsolete Ever needed a microphone for your project. This tiny little board will fulfill all your needs - it is not only mobile, but as well easy to connect. A low power, efficient, omnidirectional AMP401 microphone has an analog output. It works great for near and long range uses and is particularly suitable for a mobile projects given its extremely low energy consumption. You can use it in a range of applications - we can see it used in smartphones, cameras or electronic nannies. Code SP021
Kit Seeed Grove 30 sensors for Arduino The kit includes 30 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes. Code SS002 Last items in stock Price €79.00
SparkFun Pi Servo HAT - Obsolete 16 servo motors with one board seems impossible? With this board not only it isn´t impossible, but it even seems easy. Additionally, you won´t need to sacrifice any of your valuable GPIOs as the HAT connects directly via I2C. Additionally, you have a serial terminal connection at your disposal. You can supply the power to the board through your Pi or directly if you are going for larger servos and would need a separate source of power. Simply scrap a small blob of solder on the isolation jumper. Code SP0016 ✗ Out-of-Stock Price €14.04
Kit Seeed Grove 40 sensors for Arduino The kit includes 40 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes. Code SS003 ✗ Out-of-Stock Price €90.83
Pimoroni Explorer HAT Pro If you are into prototyping with your Raspberry (which you should be given that is what the board is for), Pimeroni Explorer HAT Pro is a great solution for you. Board is equipped with a range of inputs and outpu, which enables it to achieve range of potential applications from controlling motors, to analog sensors and 5V systems. As any Pimeroni accessory it is well compatible with all Raspberry boards and comes in with a range of Pythong libraries on github issued by Pimeroni team themselves Code PI0003 Backorder Price €23.96
Pimoroni Pico Scroll Pack - White The 17 x 7 rectangular matrix has a total of 119 white LEDs that can be controlled individually. A dedicated extension to the Raspberry Pi Pico. The device uses the 12C bus for communication and can be safely powered via the USB port. Code PI044 Last items in stock Price €17.76
Expansion Board GPIO Shield 40 Raspberry Pi B+ Pin Expansion Board GPIO Shield 40 Raspberry Pi B+ Pin features: - Shield module for Raspberry Pi 2 and Pi 3, B and B + Code RA013 Available Price €5.66
Capacitive Fingerprint Scanner - UART (AD-013) - OBSOLETE This fingeprint scanner from ADH-Tech combines a highly precise fingerprint sensor module with an onboard MCU and UART interface enabling trivially very connection to any project. The scanner independently reads and analyses the fingerprint thanks to an MCU algorithm that can send a converted digital signal to a peripheral serial interface for a data read. The onboard MCU algorithm enables operations such as for example a fingerprint enroll. Code SP036
DS3231 Precision RTC Real Time Clock Module AVR ARM DS3231 Precision RTC Real Time Clock Module AVR ARM features: - Can be used in projects of Arduino, Raspberry Pi, PIC, AVR- Function compatible with the DS 3231- Power supply voltage: +2.3 V to +5.5 V- Temperature range: -40 ° C to + 85 ° C- Low energy consumption- Full clock calendar functions that include seconds, minutes, hours, date, month and year and valid until leap year compensation- Two alarm calendar- Interface: I2C Code RA011 Available Price €2.44
SparkFun Qwiic HAT for Raspberry Pi The Qwiic HAT is an absolute basic of Qwiic system for Raspberry. It enables a quick and efficient connection of an sensor to your Raspberry over I2C bus (GND, 3.3 V, SDA and SCL). As Qwiic enables daisy chaining of components, you can pretty much install as many sensors on the Qwiic HAT as you want. On top of that it fits perfectly Pi Tin enclosure from SparkFun enabling connection while in case. Code SP031 Available Price €6.60
SparkFun MEMS Microphone Breakout - INMP401 (ADMP401) - obsolete Ever needed a microphone for your project. This tiny little board will fulfill all your needs - it is not only mobile, but as well easy to connect. A low power, efficient, omnidirectional AMP401 microphone has an analog output. It works great for near and long range uses and is particularly suitable for a mobile projects given its extremely low energy consumption. You can use it in a range of applications - we can see it used in smartphones, cameras or electronic nannies. Code SP021
Kit Seeed Grove 30 sensors for Arduino The kit includes 30 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes. Code SS002 Last items in stock Price €79.00
SparkFun Pi Servo HAT - Obsolete 16 servo motors with one board seems impossible? With this board not only it isn´t impossible, but it even seems easy. Additionally, you won´t need to sacrifice any of your valuable GPIOs as the HAT connects directly via I2C. Additionally, you have a serial terminal connection at your disposal. You can supply the power to the board through your Pi or directly if you are going for larger servos and would need a separate source of power. Simply scrap a small blob of solder on the isolation jumper. Code SP0016 ✗ Out-of-Stock Price €14.04
Kit Seeed Grove 40 sensors for Arduino The kit includes 40 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes. Code SS003 ✗ Out-of-Stock Price €90.83
Pimoroni Explorer HAT Pro If you are into prototyping with your Raspberry (which you should be given that is what the board is for), Pimeroni Explorer HAT Pro is a great solution for you. Board is equipped with a range of inputs and outpu, which enables it to achieve range of potential applications from controlling motors, to analog sensors and 5V systems. As any Pimeroni accessory it is well compatible with all Raspberry boards and comes in with a range of Pythong libraries on github issued by Pimeroni team themselves Code PI0003 Backorder Price €23.96