TRRS jack adapter 3.5mm female audio with PCB board

2 Channel Relay Module DC 12V 10A Low/High Trigger for Arduino features:
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 12V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator: For each channel
- Dimensions: 40x 50mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

The 2.5mm female jack connector is a connector to provide power to computers, LED TVs, routers, etc ...
This 2.5mm female jack connector adapter soldered on a PCB board, is ideal for use in our projects.
It has connection points where we can easily solder some pins to connect it directly to a breadboard, or solder a cable over those same connection points.
Adapter 2.5mm female power jack with PCB features:
- Connector type: 2.5mm female jack ,
- Color: black,
- Nominal voltage: 12v DC,
- Maximum current: 0.5A DC,
- Insulation resistance: ‰ ¥ 100MΩ,
- Operating temperature: -25ºC to + 85ºC,
- Number of output pins: 3
- Pitch between output pins: 2.54mm.

It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4
- Operation: 5V
- Power (max): 5-12V
- Total I / O pins: 20
- PWM pins: 5
- Analog pins: 12
- Maximum current of I / O pins: 40 mA
- Maximum current of pin 3.3V: 50 mA
- Flash memory: 32 KB (4 KB used by the bootloader)
- SRAM: 2.5 KB
- EEPROM: 1 KB
- Speed: 16 MHz
- external interrupt
- TWI / I2C, UART, SPI interfaces
- Dimensions: 18x33mm
- Weight: 30 grams

The L293D motor controller allows you to control two DC motors or one stepper motor using Arduino kits. The system allows you to adjust the direction and rotational speed of motors with a current consumption of up to 600 mA and a supply voltage from 4.5 V to 25 V.

Alligator clip connectors Red and  Black.

Double Cable 26AWG Red Black Flexible PVC - 0,13mm² Prototype features:
- Ideal for your electronic projects.
- Length: 1m
- Conductor: flexible copper
- Insulation: PVC
- Low voltage electric cables
- Cable type: 26AWG
- Resistance to 20ºC: 133.9 Ohm / Km
- Diameter: 0.40mm

The official Raspberry 4 power supply with USB-C connector up to 3.1 A in white.

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles