Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.08
8x8 LED Matrix Kit MAX7219 Arduino compatible PIC Dot Matrix Display Cascade DIY 8x8 LED Matrix Kit MAX7219 Arduino PIC Dot Matrix Display Cascade DIY features: - 8X8 LED matrix controlled by MAX7219 chip - 3mm red LED - SPI communication - Voltage: 4.7 - 5.3V DC - Interfaces to manage multiple modules in cascade - Matrix dimensions: 32mm x 32mm x 8mm - PCB dimensions: 32mm x 50mm Code M0062 Available Price €2.95
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE - Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base - This module is very similar to HM-10 module - Bluetooth protocol: Bluetooth V4.0 BLE specification - Ultra-low power consumption, in 90uA standby mode Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features: - Chipset based on CC2541 - Bluetooth Class 2 - Industrial level Bluetooth module SPP - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) Code W0078 Available Price €4.95
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.69
VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features: > - Input voltage 2.5V-3V - Operating power 60mW / 15fps VGA YUV - Resolution VGA 640x480 pixels (30fps) - Maximum frame rate 30fps VGA - Flicker 50Hz / 60Hz automatic detection - Lens size 1/6 " - Angle of view 25 ° - Sensitivity 1.3V / (lux- seg) - SCCB (Serial Camera Control Bus) interface - Output format · 8 Bits - YUV / YCbCr 4: 2: 2 - RGB 565/555/444 - GRB 4: 2: 2 - RAW RGB data - High sensitivity Light operation - Automatic adjustment - Color level saturation - Edge enhancement - Noise level Code M0103 Available Regular price €5.79 -€1.00 Price €4.79
120x Female-Male Cables Female-Female Male-Male Dupont Jumpers 2.54 for Arduino 120x Female-Male Cables Female-Female Male-Male 2.54 Jumpers Dupont Arduino features:- Length: 20cm- Quantity: 120 cables- Female-Female 40 units- Male-Male 40 units- Female-Male 40 units Code K0103 Available Regular price €7.47 -€1.48 Price €5.99
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.89
Aluminium Robot 6 DOF Arm without servo The 6 DOF black aluminum arm is widely used in the field of teaching, the personal production of IDY and the education of the fanatics, it can be seen as a demonstration platform of multiple degrees of freedom, and its energy system consists of six servomotors, Robot can be achieved before and after, Up and down, left and right to grasp the handling of the presentation. Aluminium Robot 6 DOF Arm without servo features: - Material: 2mm thick aluminum plate - Color: Black Code R0071 Last items in stock Price €49.00
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE - Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base - This module is very similar to HM-10 module - Bluetooth protocol: Bluetooth V4.0 BLE specification - Ultra-low power consumption, in 90uA standby mode Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features: - Chipset based on CC2541 - Bluetooth Class 2 - Industrial level Bluetooth module SPP - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) Code W0078 Available Price €4.95
SparkFun ESP32 Thing The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right? Code SP009 Last items in stock Price €27.99
Wireless Module Arduino compatible HC-05 HC05 Bluetooth The bluetooth HC-05 module is one of the best options for projects where you need wireless communications. The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features: - CSR BC417 Chipset - Power: 3.3. - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz ISM band - Modulation: GFSK - Approximate range: 10m - Security: Authentication and encryption - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port temperature: -20 ºC to +75 ºC Code W0019 ✗ Out-of-Stock Price €8.90
BLE 4.0 UART Bluetooth Low Energy Module without Adapter This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burnHM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, supportIn commands.You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features: - Version AT-09 CC2541 Arduino Android IOS BLE- Serial transceiver Code W0087 Available Price €5.31
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €5.39
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €5.39
USB DC 5V Bluetooth Audio USB DC 5V Bluetooth Audio features: - You can connect it with your smartphone - Power: DC 5V micro USB - Speaker: 4 ~ 8 Ohm - Audio Jack: 3.5mm - SD card: support MP3 / WMA / WAV / FLAC format - The transmission distance could be up to 10m - Size: 50 x 40 mm Code M0067 ✗ Out-of-Stock Price €5.79
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Last items in stock Price €5.90
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Available Price €7.49
Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE for Arduino Master Slave Bluetooth Modul for Arduino iOS Android. The HM10 supports Bluetooth 4.0 (low energy) and therefore has a relatively low power consumption. Code W0126 Available Price €7.95
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE - Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base - This module is very similar to HM-10 module - Bluetooth protocol: Bluetooth V4.0 BLE specification - Ultra-low power consumption, in 90uA standby mode Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features: - Chipset based on CC2541 - Bluetooth Class 2 - Industrial level Bluetooth module SPP - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) Code W0078 Available Price €4.95
SparkFun ESP32 Thing The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right? Code SP009 Last items in stock Price €27.99
Wireless Module Arduino compatible HC-05 HC05 Bluetooth The bluetooth HC-05 module is one of the best options for projects where you need wireless communications. The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features: - CSR BC417 Chipset - Power: 3.3. - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz ISM band - Modulation: GFSK - Approximate range: 10m - Security: Authentication and encryption - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port temperature: -20 ºC to +75 ºC Code W0019 ✗ Out-of-Stock Price €8.90
BLE 4.0 UART Bluetooth Low Energy Module without Adapter This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burnHM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, supportIn commands.You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features: - Version AT-09 CC2541 Arduino Android IOS BLE- Serial transceiver Code W0087 Available Price €5.31
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €5.39
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €5.39
USB DC 5V Bluetooth Audio USB DC 5V Bluetooth Audio features: - You can connect it with your smartphone - Power: DC 5V micro USB - Speaker: 4 ~ 8 Ohm - Audio Jack: 3.5mm - SD card: support MP3 / WMA / WAV / FLAC format - The transmission distance could be up to 10m - Size: 50 x 40 mm Code M0067 ✗ Out-of-Stock Price €5.79
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Last items in stock Price €5.90
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Available Price €7.49
Bluetooth Wireless Module 4.0 CC2541 Android IOS HM-10 BLE for Arduino Master Slave Bluetooth Modul for Arduino iOS Android. The HM10 supports Bluetooth 4.0 (low energy) and therefore has a relatively low power consumption. Code W0126 Available Price €7.95