Resistor 220 Ohm 5% 0,25W 1/4W Resistor 220 Ohm 5% 0,25W 1/4W features:-220 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0008 Available Price €0.08
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €3.49
Battery holder 2x AA 3V Battery holder 2x AA 3V features: - Cable 15cm long - Measurements 59x 33x 16mm - Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7) Code PP002 Available Price €0.99
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €9.99
Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.2mm Tin ideal for application in consumer electronics circuits.Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.2mm features:- 100gr. 1.2mm diameter welding wire- 60% tin and 40% lead- Fusing temperature 183 „ƒ / 190 „ƒ- Alloy Sn60 Pb40- Flux 2.5%- Quantity: 1 unit- High quality - manufactured in EU Code Q0003 ✗ Out-of-Stock Price €8.95
Water Flow Sensor 1-30l /Min YF-S201 The meter built on the basis of a water rotor and a Hall effect sensor Please note this is not a Accuracy. Pulse rate varies slightly depending on flow rate, fluid pressure, and sensor orientation. Water Flow Sensor 1-30l /Min YF-S201 features: - Working voltage range: DC 5 ~ 18 V - Allow pressure: water pressure below 1.75Mpa - Accuracy (flow-pulse output): ± 1 ~ 30 l / min - Use temperature: ‰ ¤ 80 ° C - Load capacity: ‰ ¤ 10 mA (5Vdc) - Operating humidity: 35% ~ 90% RH (frost free) - Temperature: -25 ~ + 80 ° C - Outlet diameter: 1/2 " - Red wire: positive supply - Wire Black: negative power supply - Yellow Cable: signal output - Color: black - Size: 6.2x3.6x3.4 cm Code M0109 ✗ Out-of-Stock Price €5.95
Momentary Switch Push Button Black N/O 7mm Momentary Switch Push Button Black N/O 7mm features: - Momentary pushbutton N/O (normally open)- Black button- Dimensions approx. 7 mm x 27 mm- Recessed with nut and washer- Load current (supported): 1A to 230V / 2A to 125V- Drill to embed: 7 mm +/- 0.2- Operating temperature: -55ºC to + 85ºC Code K0157 Available Price €0.45
Servo 9g SG92r 2.5kg 9g digital servo new version of SG90. POM with Carbon fiber gears set and control arms are more durable use than SG90 nylon gear and more torque. It is a good choice for park size 3D models , high speed jets and R/C airplane 250 450 RC helicopter Servo 9g SG92r 2.5kg features: Weight: 9g Operating voltage: 4.8v Stall torque: 2.5kg /cm(4.8v) Gear type: POM with carbon fiber Operating speed: 0.1sec /60degree (4.8v) Temperature range: 0„ƒ_ 55„ƒ Dead band width:1us servo wire length: 25 cm Servo Plug: JR (Fits JR and Futaba) servo arms &screws included and fit with Futaba servo arm Code R0079 Available Price €4.30
Raspberry Pi 2-3 Model B Multifunction Expansion GPIO Module This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included. The module offers a set of mini jumpers to configure the GPIO. Code RA016 Available Price €7.95
SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino features: - GSM / GPRS SIM900 module-based development card / shield from Simcom - The shield allows you to get SMS, MMS, GPRS and audio via UART by sending AT commands (GSM 07.07, 07.05 and SIMCOM Enhanced COM Commands). - The shield also has 12 GPIOs, 2 PWMs and a ADC of the SIM900 module (All of them are 2V8 logic) present on board. - Quad-Band 850/900/1800/1900 MHz: it would work on GSM networks in all countries of the world. - GPRS multi-slot class 10/8 - GPRS mobile station class B - Complies with GSM phase 2/2 + - Class 4 (2 W @> Code W0090 Available Regular price €25.99 -€3.50 Price €22.49
SIM800L GPRS GSM SIM Board Quadband SIM800L GPRS GSM SIM Board Quadband features: Package includes: - SIM800L module, - 2x pin headers, - Spring antenna, - 3G PCB antenna - 15cm cable. - Supported SIM format: Micro SIM. Code W0017 Available Price €6.49
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €7.49 -€1.29 Price €6.20
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 Available Price €21.95
SSR-25 DD 25A DC-DC Solid State Relay 5V-60VDC output The DC-DC 25A solid state relay has a 3-32VDC input and a 6-60VDC output. It has a maximum load capacity of 25A. It has a long operating life and high reliability, a compact size. This relay switches very quickly. Fotek SSR-25 DD 25A DC-DC Solid State Relay 5V-60VDC output Code RL017 Available Price €7.99
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 ✗ Out-of-Stock Price €4.99
W5500 Ethernet Network Modules SPI 8 sockets The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this module. It can be used as a server or as a client. Code W0105 Available Price €9.99
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €9.50
Qwiic cable 100mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long Code SP022 Available Price €1.99
Raspberry Pi 2-3 Model B Multifunction Expansion GPIO Module This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included. The module offers a set of mini jumpers to configure the GPIO. Code RA016 Available Price €7.95
SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino features: - GSM / GPRS SIM900 module-based development card / shield from Simcom - The shield allows you to get SMS, MMS, GPRS and audio via UART by sending AT commands (GSM 07.07, 07.05 and SIMCOM Enhanced COM Commands). - The shield also has 12 GPIOs, 2 PWMs and a ADC of the SIM900 module (All of them are 2V8 logic) present on board. - Quad-Band 850/900/1800/1900 MHz: it would work on GSM networks in all countries of the world. - GPRS multi-slot class 10/8 - GPRS mobile station class B - Complies with GSM phase 2/2 + - Class 4 (2 W @> Code W0090 Available Regular price €25.99 -€3.50 Price €22.49
SIM800L GPRS GSM SIM Board Quadband SIM800L GPRS GSM SIM Board Quadband features: Package includes: - SIM800L module, - 2x pin headers, - Spring antenna, - 3G PCB antenna - 15cm cable. - Supported SIM format: Micro SIM. Code W0017 Available Price €6.49
ESP32 WROOM-32 DEVKIT V1 - Board with WiFi and Bluetooth WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins. Code W0103 Available Regular price €7.49 -€1.29 Price €6.20
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 Available Price €21.95
SSR-25 DD 25A DC-DC Solid State Relay 5V-60VDC output The DC-DC 25A solid state relay has a 3-32VDC input and a 6-60VDC output. It has a maximum load capacity of 25A. It has a long operating life and high reliability, a compact size. This relay switches very quickly. Fotek SSR-25 DD 25A DC-DC Solid State Relay 5V-60VDC output Code RL017 Available Price €7.99
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 ✗ Out-of-Stock Price €4.99
W5500 Ethernet Network Modules SPI 8 sockets The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this module. It can be used as a server or as a client. Code W0105 Available Price €9.99
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €9.50
Qwiic cable 100mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long Code SP022 Available Price €1.99