Double Side Prototype Board PCB 8x12cm Double Side Prototype Board PCB 8x12cm features: -Thickness of PCB: 1.6mm-Material: high quality FR-4 glass fiber PCB-Presented and numbered on both sides-Top and bottom are identical copper layers-Pads grid (pitch) 2.54mm/0.1", hole diameter 0.9mm Code PB018 Available Price €2.69
Compact Digital non-contact laser tachometer RPM DT2234C+ Compact instrument that measures the speed of rotation with a visible red light beam from a powerful LED. The high intensity class II laser measures wide measurement range and high resolution, from 2.5 to 99.999 RPM (Revolutions per Minute) Code H0193 Available Regular price €16.49 -€2.00 Price €14.49
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.69
Infrared LED Flame Sensor 5mm module Led module infrared sensor for ArduinoDetector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm module features:- 4 Pins Output: - A0: analog output - D0: digital output - GND: ground connection - VCC: 5V module power- Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino. Code S0133 Available Price €1.39
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.89
Batch of 600 Units 1/4W Resistors Various values Ohm Ω Batch of 600 Units 1/4W Resistors Various values Ohm Ω features: - Each lot contains (30 x 20 units): 10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M - Tolerance: ± 5% - Power: 0.25W Code D0070 Available Price €3.95
DC 10A Analog Panel Ammeter 0 to 10A DC 10A Analog Panel Ammeter 0 to 10A features: - DC 10A Ammeter Instrument Analog Amperage meter panel with shunt- Type: Analogue ammeter- Range: DC 0-10A- Accuracy: class 2.5- Size: 51 × 51 × 46mm- Complete with screws for simple DIY installation- This meter has a built-in bypass, does not need external derivation Code H0043 Available Price €2.69
L293D Motor Drive Shield Expansion Board It allows controlling many different types of engines: - Up to 4 bidirectional current motors- Up to 2 stepper motors (unipolar or bipolar) In addition it is provided with two connectors for servos. L293D Motor Drive Shield Expansion Board features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A (650mA)- Logic voltage: 5V- Controller L293D- Measures: 70x55x20 mm L293D controller consists of 4 H bridges with 650 mA current with thermal protection.Pull-down resistors keep the motors off during startup. Code R0001 Available Price €2.95
DS3231 Precision RTC Real Time Clock Module AVR ARM DS3231 Precision RTC Real Time Clock Module AVR ARM features: - Can be used in projects of Arduino, Raspberry Pi, PIC, AVR- Function compatible with the DS 3231- Power supply voltage: +2.3 V to +5.5 V- Temperature range: -40 ° C to + 85 ° C- Low energy consumption- Full clock calendar functions that include seconds, minutes, hours, date, month and year and valid until leap year compensation- Two alarm calendar- Interface: I2C Code RA011 Available Price €2.95
Time Switch Module 12V NE555 Monostable Switch Delayed This module is a timed switch that allows you to program several types of applications such as lights. Time Switch Module 12V NE555 Monostable Switch Delayed features: Code M0160 Available Regular price €4.59 -€0.59 Price €4.00
Capacitive Fingerprint Scanner - UART (AD-013) - OBSOLETE This fingeprint scanner from ADH-Tech combines a highly precise fingerprint sensor module with an onboard MCU and UART interface enabling trivially very connection to any project. The scanner independently reads and analyses the fingerprint thanks to an MCU algorithm that can send a converted digital signal to a peripheral serial interface for a data read. The onboard MCU algorithm enables operations such as for example a fingerprint enroll. Code SP036
VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. AL422B Video buffer consists of 3M-bits of DRAM, and it is configured as 393.216 x 8 bit FIFO (First In First Out). The interface is very easy to use because all operations are controlled by the internal DRAM memory controller. VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps features: - Input voltage: 2.5V-3V - Controller: AL422B FIFO buffer - Operating power: 60mW / 15fps VGA YUV - VGA resolution: 640x480 pixels (30fps), - Maximum frame rate: 30fps VGA - Flicker: 50Hz / 60Hz auto detection - Lens size: 1/6 " - Angle of view: 25 ° - Sensitivity: 1.3V / (lux- sec) - SCCB (Serial Camera Control Bus) interface - Output format: 8 Bits - YUV /> Code M0114 Available Price €14.59
Wireless Transceiver Module with Antenna CC1101 This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.This is a significant improvement over the CC1100 module.It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @> Code W0083 Available Price €8.49
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €9.50
Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 Work with Bluetooth compliant devices including notebook, PDA, digital camera,printer and mobile phone.Mini Dongle Adapter Bluetooth USB V2.0 Windows XP/VISTA/7 features:- Bluetooth specification V2.0 - Supporting profiles: networking, dial-up, fax, LAN access and handset - Operation system Windows98, 98se, Me, 2000, XP, Vista, Windows7 - Receiving/sending range: 100m Code W0093 Available Price €3.90
Passive Buzzer 5V The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features: - Input voltage: 3V to 12V - Diameter: 12mm - Height: 7.5mm - Pin spacing: 6.5mm - Impedance: 16 Ohm - Working frequency: 2 to 5 KHz - Quantity: 1 unit Code M0011 Available Price €0.39
SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino features: - GSM / GPRS SIM900 module-based development card / shield from Simcom - The shield allows you to get SMS, MMS, GPRS and audio via UART by sending AT commands (GSM 07.07, 07.05 and SIMCOM Enhanced COM Commands). - The shield also has 12 GPIOs, 2 PWMs and a ADC of the SIM900 module (All of them are 2V8 logic) present on board. - Quad-Band 850/900/1800/1900 MHz: it would work on GSM networks in all countries of the world. - GPRS multi-slot class 10/8 - GPRS mobile station class B - Complies with GSM phase 2/2 + - Class 4 (2 W @> Code W0090 Available Regular price €25.99 -€3.50 Price €22.49
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Available Price €11.89
LED Module Full Color RGB Bulb KY-016 This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately. The LED Bulb Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three colors. primary (red, green and blue). These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package. Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors. Code M0081 Available Price €2.95
Sonoff DUALR3 Lite - Wireless Smart Switch SONOFF DUALR3 is a WiFi based 2-gang switch that can independently connect and control two connected devices or lights - this simply means that 1 SONOFF DUALR3 control switch is equivalent to 2 Sonoff basic switches! Code WS046 Available Price €12.99
Bus Pirate - v3.6a This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board. This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin. Code SP037 Last items in stock Price €39.99
ESP8266 ESP12E WiFi NodeMcu + Motor Drive L293D Expansion Shield Board Kit NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, Code W0016 Available Price €8.44
SenseCAP K1100 - Sensor kit with LoRa and AI - "SenseCAP K1100 - The Sensor Prototype Kit with LoRa® and AI allows you to quickly digitise your world with LoRaWAN® and solve real-world challenges. With this plug-and-play toolkit, anyone can add artificial intelligence to their edge devices and unlock the potential of AIoT. Code SS049 Last items in stock Price €78.99
Sonoff T0EU1C-TX Gang 86 Smart WiFi Wall Touch Switch WiFi Smart Wall Switch Sonoff T1 Gang 86 Smart WiFi RF APP Touch Control Wall Light Switch features:works with Amazon Alexa, Google Assistant DIY Smart Home, Nest via iPhone Android. Code W0089 Available Regular price €19.90 -€1.91 Price €17.99
Raspberry Pi v2 Oficial Camera - Sony IMX219 8 Megapixel Sensor HD V2 Raspberry Pi camera board The Raspberry Pi High Definition (HD) camera board connects to any Raspberry Pi or Compute Module to create HD photos and video. Uses Sony's IMX219PQ image sensor that offers high-speed, high-speed video images Sensitivity. Raspberry Pi Camera Module offers reduced image contamination such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection. Raspberry Pi Camera Board, Sony IMX219 8 Megapixel Sensor features: High-quality images High data capacity Fixed 8 megapixel focus (includes focus adjustment tool) Compatible with 1080p, 720p60 and VGA90 Sony IMX219PQ CMOS image sensor 15-pin ribbon cable Code RA053 Last items in stock Price €29.89
PAM8610 2X10W Dual Channel Amplifier The amplifier with high efficiency, in case of 12 V power supply can output 10 W + 10 W power. Code M0209 Available Price €3.55
Qwiic cable 100mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long Code SP022 Available Price €1.99
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 ✗ Out-of-Stock Price €5.39