DC voltage sensor 0-25v for Arduino

NodeMcu module based on ESP8266 controller and programming in Lua language. 
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. 
It works as a standard WiFi 802.11 b / g / n 2.4 GHz. 
USB communication - the CP2102 chip. Characteristic of ESP 12E: 
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), 
- Supported protocols: 802.11 b / g / n, 
- Network support: 2.4 GHz, 
- Band: 2400 (MHz), 
- Wi-Fi Direct (P2p), Soft Access Point, 
- TCP Stack / Integrated IP, 
- PLLs, Regulators and Integrated Power Management Units, 
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode,

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

Relay SRD-05 DC-2P 5V 10A SPDT features:
- Supply voltage: 5V
- Output Current: 10A
- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica

CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features:
- Content:
* 1x UNO R3 CH340 Compatible with Arduino
* 1x CNC Shield V3
* 4x A4988 Drivers
* 4x Heatsinks for A4988
* Jumpers

Buzzer alarm to convert electrical signals into intermittent acoustic signals in robotic devices and Arduino projects

A buzzer with a pulsating tone generator, after connecting the supply voltage (DC) in the range of 3V -24V, the buzzer generates an intermittent signal with a frequency of approximately 1 Hz. Application example: as a reverse alarm system for a car. 

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

WIFI transceiver based on the ESP8266 controller.
It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low power mode:

It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 50mm long

USB DC 5V Bluetooth Audio features:
- You can connect it with your smartphone
- Power: DC 5V micro USB
- Speaker: 4 ~ 8 Ohm - Audio Jack: 3.5mm
- SD card: support MP3 / WMA / WAV / FLAC format
- The transmission distance could be up to 10m
- Size: 50 x 40 mm

Relay 5VDC SPDT 5VDC JQC-3FF for industrial applications, automation and process control and consumer electronics. Relay SPDT JQC-3FF 5VDC-1ZS features:
- Coil voltage: 5 VDC,
- Coil power: 360 mW,
- Switching capability:
 - 10A @ 277 VAC
 - 12A @ 125 VAC
- Operating time: between 5ms and 10ms,
- Plastic sealed and flux proofed types available,
- Environmental friendly product (RoHS compliant),
- Working temperature: -40ºC to 70ºC,
- Outline dimensions: 19.0 x 15.2 x 15.5 mm.