Capacitive Touch Sensor Module TTP229 - 16 Touch Sensitive Pads

NodeMcu module based on ESP8266 controller and programming in Lua language.
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC.
ESP8266-12E is an improved version of ESP8266-12.
It works as a standard WiFi 802.11 b / g / n 2.4 GHz.
USB communication - the CH340 chip. Characteristics of ESP 12E:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- TCP Stack / Integrated IP
- PLLs, Regulators and Integrated Power Management Units
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode

The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features:

- Input voltage: 3V to 12V
- Diameter: 12mm
- Height: 7.5mm
- Pin spacing: 6.5mm
- Impedance: 16 Ohm
- Working frequency: 2 to 5 KHz
- Quantity: 1 unit

This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.
Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.
The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burn
HM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, support
In commands.
You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features:
- Version AT-09 CC2541 Arduino Android IOS BLE
- Serial transceiver

The bluetooth HC-05 module is one of the best options for projects where you need wireless communications.
The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features:
- CSR BC417 Chipset
- Power: 3.3.
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Approximate range: 10m
- Security: Authentication and encryption
- Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps
- Supports AT commands for configuration through a serial port
temperature: -20 ºC to +75 ºC

LED green.
The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Green features:
- Operating voltage: 3 - 5 VDC
- Very bright
- Density of the PCB: 0.8 mm
- LED color: green
- Size: 5.5x12.5 mm
- 1 LED included

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level

Lilypad Battery Support Button Cell 3V CR2032 features:
- Battery holder for your Lilypad projects
- For 20mm diameter battery type CR2032
- ON / OFF control
- Connection points: 4

Raspberry Pi HD Pi NoIR V2 camera board Raspberry Pi HD Pi NoIR camera board connects to any Raspberry Pi or Compute Module to create HD photos and video. The Pi NoIR (without infrared) is the same as the standard camera module but without an infrared filter. Therefore, it is excellent for photography and video in the dark.
The module uses Sony's IMX219PQ image sensor that offers high-speed, high-sensitivity video images.
The Pi NoIR module offers contamination from Reduced image such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection. Raspberry Pi NoIR Camera Board, Sony IMX219 8 Megapixel Sensor features:
and benefits: No infrared filter
High quality images

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

TinyS3 is the latest in Unexpected Maker's popular range of "Tiny" development boards. It's packed with amazing features and peripherals, wireless connectivity, and stacks of Flash and PSRAM, all in the same tiny package size as the original TinyPICO!