Set of M2, M3, M4 screws 330 pcs.

Desoldering iron for the removal of excess tin. You can quickly and effectively remove solder from a plate or circuit.
Replaceable antistatic nozzle.
Manufactured in Aluminum.
Aluminum Desoldering Pump Tin Antistatic Suction features:
- Length: 190mm
- Desoldering pump
- High suction power
- Replaceable long-life silicone tip
- Light weight
- Easy use with one hand, light and resistant
- Vacuum Solder Aluminum Desoldering Pump Solder Remover Pump Tool
- A good quality product for fast and efficient removal of excess solder, ideal for PCB repair
- High-capacity spring-loaded plunger quickly eliminates welding in one action. The Pumping tool easily
- Disassemble for a quick clean

The integrated mainboard driver MKS-GEN L V1.0 for 3D printer has been developed by Makerbase to optimize existing problems on the open source controller board such as Ramps 1.4.
This product offers more flexible options for users.
MKS-GEN L V1.0 Integrated Controller Compatible with Ramps 1.4/Mega2560 R3 features:
- Mega2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.
- Supports a variety of step-by-step drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change stepper motors and motors that users like.
- Reserve the signal from the external controller, available to connect an external high current driver to drive stepper motors 57 and 86.
se high quality MOSFET, better cooling and more stable.

10x Electrolytic Capacitor 100 uF 25V 105ºC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 100uF
-Maximum tension: 25V
-Maximum temperature: 105º C
-Dimensions: 6x11mm
-Quantity: 10 units

Type of chemical preparation: alcoholic stripper of printed PCB plates.
Alcohol-based cleaner to eliminate fluxes, dirt removal, flux residues in PCB.
has low impact on electronic components.
Alcohol PCB Cleaner 1l features:
- Form: liquid
- Capacity: 1l
- Alcohol PCB cleaner
PCB cleaner based on alcohol for the elimination of any residue from the printed circuit surfaces after welding, cleaning of the welding unit frames, templates and rosin screens, and the dissolution of the waste stream.
The liquid does not affect the substrate or components of the circuit board.

Resistor 200R Ohm 5% 0,25W 1/4W features:
-200R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

It is a very ideal tool when the third hand is required.
Helping Magnifying Hand Tool features:
- Magnifying glass diameter 60mm
- Weight: 0.5kg
- Dimensions: approx. 15 (26) x 17 x 7cm 

Thermally Conductive Silicone Paste H facilitates the transfer of heat between the electronic components and the radiator. It is necessary for the correct operation of any type of temperature sensors. Global coefficient of heat transfer at 0-150 ° C: 0.88 W / m K

LITHIUM POLYMER BATTERY Battery LIPO 210mAh 3.7V features:
-Battery type-lithium polymer. - Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 210 mAh. - Embedded PCM security chip (protection against overcharging, over discharge, short circuit) Dimensions: -Length / depth of battery- 25mm -Battery width / diameter- 31 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output.