Mobile
- The ideal kit to build a robot car- Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included) 2WD Smart Robot Car Kit DIY features: - Robot platform with 2 wheels and idler- UNO CH340 board compatible with Arduino- Prototype plate 170 points- Micro servo 9g- Platform for servo- Distance sensor HC-SR04- Sensor shield for sensors- L298N motor controller Motor 2WD Smart Robot Car Kit DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Helpful Links: Realization of a robot manageable by Infrared
- The ideal kit to build a robot car- Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included)
- Robot platform with 2 wheels and idler- UNO CH340 board compatible with Arduino- Prototype plate 170 points- Micro servo 9g- Platform for servo- Distance sensor HC-SR04- Sensor shield for sensors- L298N motor controller Motor
- Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Helpful Links: Realization of a robot manageable by Infrared - Fix a prototype plate 170 points in the Mini Kit Robot Car 2WD DIY- Fix an IR remote control module + Infrared IR command VS1838 Realization of a robot manageable by Bluetooth - Fix a prototype plate 170 points in the Mini Kit Robot Car 2WD DIY- Fix a wireless Bluetooth module HC-06 Realization of a robot capable of automatically detecting obstacles - Fix a prototype plate 170 points in the Mini Kit Robot Car 2WD DIY- Fix a distance sensor module HC-SR04 with its support in the 2WD DIY Mini Robot Car Kit
IR Remote Control + IR Infrared Receiver VS1838 features: - The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal - Vcc supply: 3.3V-5V - IN digital output to connect to the port Arduino I / O - Remote measurements 85x 40x 5mm - Includes battery Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry: Send / Receive information via IR - Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module - Light a 3mm red LED by Infrared
Prototype Protoboard Breadboard 170 points Arduino features:- 170 connections- Base with adhesive to attach it to the work surface- Measurements: 45x35x9mm- Various colors
Ideal for building a car with obstacle detector, light followerIncludes battery compartment for 4 AA batteries and ignition switch. (batteries not included) 2WD Robot Smart Car Chassis 2x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm
It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles
- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B
Arduino Sensor Shield V5 APC220 features: Sensor Shield V5.0 allows: - Being punctured directly to an Arduino Uno, Mega, Leonardo plate- Facilitate the connection of different modules, such as sensors, relays, servos, buttons, potentiometers and more
It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection />
Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm
Tilt Camera Platform Anti-Vibration Camera Mount for Aircraft FPV features:- Platform for Arduino Robotics Modeling, works with servo 9g SG90- Servos not included
10x MALE CABLES 10cm Male Jumpers Dupont 2,54 features: -Length: 10cm -Quantity: 10 wires -Dupont male connectors on both ends -Compatible with 2.54mm female connectors -High quality and good working condition -Easy to install and use
10x Female-Female Cables 20cm Jumpers Dupont 2,54 features: -Length: 20cm-Quantity: 10 cables-Connectors have female header contacts at either end -Compatible with male connectors 2,54mm-High quality and good working conditions-Easy to install and use
29,99 tax excl.
Available