CMOS TTL logic tester

This attenuator allows the oscilloscope to measure the fuel injector and primary ignition waveforms. Passive attenuator with a 20:1 attenuation Therefore, if a 20V signal is introduced, it will emit a 1V signal. Using this element, the oscilloscope can measure voltage higher than its range (*20V)

The UT58 series is a safe and reliable hand-held digital multimeter that is easy to operate. Its large 60mm x 54mm LCD screen conveniently displays your measurement results. This series of digital multimeter caters to a variety of applications in the electrical and electronic fields

This modern and compact digital multimeter has a large 4-digit LCD display that offers a great experience to the user. Voltage / current / resistance / capacitance / frequency analysis, bem as diode and continuity test. Max. Digits: 1999 3 ½ digits

This multimeter meets IEC61010 standards: no pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation.

8-channel oscilloscope for vehicle testing.
More than 80 kinds of automotive diagnostic functions (ignition detection / sensor / bus detection / performance / starting and charging circuits , etc.). The video help function provides the diagnostic video help that can be viewed online. The diagnostic result can be generated a diagnostic report, printed or taken a screenshot by pressing a key, many methods to save the data. Supported for recording waveform for a long time. You can simulate the camshaft and crankshaft signal. Transmit signals through the USB 2.0 plug and play interface, and requires no additional power supply; Key Hantek 1008C PC Oscilloscope USB 8 Channel Automotive Diagnostic DAQ features:

The voltage / power / battery level indicator KA2284 contains five LED lights that light up progressively as the voltage increases, from green to red to yellow.
It is ideal for your projects that require voltage level indicators, such as battery capacity and audio level indicators.
The built-in potentiometer adjusts the range (sensitivity) of the LED display, and the DC or AC input can be selected via the P2 bridge.
The AC and DC input can be controlled with bridge P2: bypassed for DC, open for AC.
Adjustable power level through the potentiometer. Power Level KA2284 Indicator Module 5 LED features:
- Operating voltage: 3.5 - 12 VDC
- 5 level LED KA2284 controller
- Adjustable power
- 4 pin terminal:
       - IN: Input voltage to measure

UT100 series is specially designed for automobile diagnosis. Combines RPM, DWELL, and other multimeter functions. The series is useful for car maintenance personnel to diagnose traditional vehicles and hybrid electric vehicles. Applications: Its applications include working on fuses, switches, solenoids, relays, charging systems, fuel systems, engine detection, etc.

UT363 mini wind speed and temperature meters. UT363 measures wind speeds up to 30 m/s (108 km/h)

The digital clamp meters are designed according to EN61010-2010 CAT II 600V/CAT III 300V, with overload protection, high reliability, high safety and high accuracy. These meters can be used to measure high voltage frequency, AC/DC current, etc.

Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A.
The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features:
- Input voltage: 230VAC
- Output voltage: 0-30V adjustable
- Output current: 0-5A adjustable
- Backlit display
- Protection against over-consumption and short circuit
- Cooled by fan
- Includes crocodile clip cables Uni-T UTP3315TFL datasheet
Load Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.2% + 3mA
Line Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.1% + 5mA
Ripple and Noise
Voltage 1mV rms
Current 3mA rms

Digital Multimeter 890c + Ammeter Voltmeter AC DC Ohm C Buzzer features:
- Uni-T M890C + Digital Multimeter LCD AC DC Voltmeter Ammeter
- Power supply: 9V battery
- Protection: F 250mA / 250V
- Display: LCD, range up to 1999 update: 2-3/s
- Method: double A / C slope
- Indication of exceeding the range: on the screen only by the number "1"
- Polarization of traffic for negative visualization "-"
- Operating temperature: 0 °C ~ 40 °C (32 °F ~ 104 °F)
- Storage temperature: -10 °C ~ 50 °C (10 °F ~ 122 °F)
- Flat battery signal: the screen shows "BAT"
- Dimensions: 170x87x35 mm
- Weight: 215g
- Sound traffic: YES (piezo) Specifications: - DCV: 200m-2-20-200-1000V ± 0.5%
- ACV: 2-20-200-750V ± 1.0%

Modern digital multimeter with large LCD display that provides a better user experience. Voltage / current / resistance analysis, as well as diode, transistor and continuity tests.

This multimeter complies with IEC61010 standards: in pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation.