Digital Clamp Meters Uni-T UT202A+

This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed.

This Hantek CC-65 clamp is a special accessory for oscilloscope by means of BNC connector, which allows to measure the parameters and current waveforms. Its current transducer linearly transforms AC or DC current into AC or DC current voltage. By connecting the current clamp to an oscilloscope, the waveform of the current signal can be observed.

Digital Multimeter 890c + Ammeter Voltmeter AC DC Ohm C Buzzer features:
- Uni-T M890C + Digital Multimeter LCD AC DC Voltmeter Ammeter
- Power supply: 9V battery
- Protection: F 250mA / 250V
- Display: LCD, range up to 1999 update: 2-3/s
- Method: double A / C slope
- Indication of exceeding the range: on the screen only by the number "1"
- Polarization of traffic for negative visualization "-"
- Operating temperature: 0 °C ~ 40 °C (32 °F ~ 104 °F)
- Storage temperature: -10 °C ~ 50 °C (10 °F ~ 122 °F)
- Flat battery signal: the screen shows "BAT"
- Dimensions: 170x87x35 mm
- Weight: 215g
- Sound traffic: YES (piezo) Specifications: - DCV: 200m-2-20-200-1000V ± 0.5%
- ACV: 2-20-200-750V ± 1.0%

The voltage / power / battery level indicator KA2284 contains five LED lights that light up progressively as the voltage increases, from green to red to yellow.
It is ideal for your projects that require voltage level indicators, such as battery capacity and audio level indicators.
The built-in potentiometer adjusts the range (sensitivity) of the LED display, and the DC or AC input can be selected via the P2 bridge.
The AC and DC input can be controlled with bridge P2: bypassed for DC, open for AC.
Adjustable power level through the potentiometer. Power Level KA2284 Indicator Module 5 LED features:
- Operating voltage: 3.5 - 12 VDC
- 5 level LED KA2284 controller
- Adjustable power
- 4 pin terminal:
       - IN: Input voltage to measure

Laser distance meter with a range of 18 metres. Additional functions of this rangefinder are a spirit level, measure surface area and measure volume.

The JDS6600 series DDS signal generator can generate sine waves, square waves, triangle waves, pulse waves and arbitrary waves, etc. The frequency will be up to 15MHz. And it has duty cycle correction, amplitude modulation function and frequency sweep function etc. It can display output signal, amplitude and frequency at the same time. This series has amplitude frequency characteristics, and the appearance is very delicate and beautiful. It can be applied in factories, schools, research institutes and laboratories. There are 5 models, JDS6600-60M, JDS6600-50M, JDS6600-40M, JDS6600-30M and JDS6600-15M. The main difference is the maximum sine wave output frequency. JDS6600 -15MHZ is the maximum output frequency of the sine wave.

Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A.
The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features:
- Input voltage: 230VAC
- Output voltage: 0-30V adjustable
- Output current: 0-5A adjustable
- Backlit display
- Protection against over-consumption and short circuit
- Cooled by fan
- Includes crocodile clip cables Uni-T UTP3315TFL datasheet
Load Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.2% + 3mA
Line Regulation
Voltage & lt; = 0.01% + 3mV
Current & lt; = 0.1% + 5mA
Ripple and Noise
Voltage 1mV rms
Current 3mA rms

The UNI-T UT300H temperature meter, which uses the latest technology, enables temperature measurements in the range of 32°C-42.9°C. The high accuracy of the device enables fast and accurate monitoring of body temperature as well as other environmental elements, e.g. objects, food, liquids, etc.

This attenuator allows the oscilloscope to measure the fuel injector and primary ignition waveforms. Passive attenuator with a 20:1 attenuation Therefore, if a 20V signal is introduced, it will emit a 1V signal. Using this element, the oscilloscope can measure voltage higher than its range (*20V)

Network tool set (10 pieces) for the construction of telephone and network cabling (RJ45, RJ11, RJ12) in a practical closed case. Crimper, tester, cable detector, cable stripper, screwdrivers, Rj-45 connectors, etc.

Stabilized laboratory power supply with smoothly adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5A. The power supply is fan cooled which allows the power supply to work in constant mode.

Modern digital multimeter with large LCD display that provides a better user experience. Voltage / current / resistance analysis,as well as diode, transistor and continuity tests.

This multimeter complies with IEC61010 standards: in pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) and double insulation.