Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg
  • Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg

Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg

Q0027

Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg features:
A compound for etching of printed circuit boards and pickling of copper. An ideal alternative to ferric chloride. It is readily soluble and does not crystallize from the solution. It etches evenly, ensures the sharpness of contours and minimizes undercutting. Usage: Dissolve the preparation in 0.5 l of water at a temperature of 50°C. Perform etching at 40°C (max. 50°C). Bath movement ensures quicker etching. The etching solution must not be stored in hermetically sealed containers due to the risk of developing overpressure and cracks.

Termopasty
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg features:


A compound for etching of printed circuit boards and pickling of copper. An ideal alternative to ferric chloride. It is readily soluble and does not crystallize from the solution. It etches evenly, ensures the sharpness of contours and minimizes undercutting. Usage: Dissolve the preparation in 0.5 l of water at a temperature of 50°C. Perform etching at 40°C (max. 50°C). Bath movement ensures quicker etching. The etching solution must not be stored in hermetically sealed containers due to the risk of developing overpressure and cracks.

Customers who bought this product also bought

Varnish Flux LT-4

- The product protects PCB plates, allows for easier welding
- The product protects the printed circuit boards against oxidation and corrosion during storage.
- This allows a faster welding and avoids the "cold welding".
- The application method allows easy distribution of the product on the plates.
- Can be used during production, repair, maintenance and service.
Flux Varnish LT-4 Plate Protector features:
- Shape: Spray
- Capacity: 100ml
- Rosin RMA
- Meets the requirements of DIN 8511, F-SW-31, PN EN 29454 1.1.1.A.
Application:
- PCB protection against oxidation,
- Applied in the production of printed circuit boards immediately after engraving,

Q0070

Price €5.95

5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

R0038

Price €2.95

40x Female-Female Cable 10cm

40x Female-Female Cable 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont female connectors on both ends
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

K1005

Price €1.99

JST PHR-2 Female 2 PIN 2mm

It is not possible to reverse the polarity by mistake.
JST PHR-2 Female 2 PIN 2mm features:
Manufacturer JST Connector series: PH Connector: plug Connector class: female Type of connector: conduit-board Raster of contactors: 2mm Number of pins: 2 Mechanical mounting: for conduit Voltage Working: 100V Working current: 2A Working temperature: -25 ... 85 ° C Connection version: contactless technical data sheet PH series

K0209

Price €0.28

Ceramic alignment tool CD-20

The zirconium ceramic tip of the CD-200/201 combines the wear resistance of a metal tip with the non-conductive and non-inductive properties of the plastic.
Ceramic alignment tool CD-20 features:
- Length: 11.5 cm,
- Screwdriver tip: flat,
- Tip length: 2mm.
- Suitable for: potentiometers, watchmaking, electronics components.

H0150

Regular price €2.29 -€0.31 Price €1.98

Desoldering Wire 1.5mm

High grade in the absorption of tin for professionals.
Copper mesh roll for desoldering electronic components.
Desoldering Wire 1.5mm features:
- Material: Copper
- Length: 1.5m
- Width: 1.5mm
- Desoldering Braid Solder Remover Wick 1.5mm / 1.5m
- Pure copper braid construction
- Quick removal welding
- Excellent thermal for a faster and safer desoldering

H0005

Price €1.79
€12.49

10,32 tax excl.

Tax included 1
Last item
Price €12.49

Order until 4pm we will send today
30 days return