TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 Available Price €1.78
Gear Reducer Motor 6V DC 200RPM for Smart Car Gear Reducer Motor 6V DC 200RPM for Smart Car features: - Voltage: 3 to 6V DC- Speed without load: 200 RPM to 6V DC Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles - Wiring of the 6V DC 200 RPM motor with the L298N double bridge H controller module Code R0045 Available Price €1.98
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €5.36 -€2.00 Price €3.36
TP4056 Lithium Battery Charger Module 5V Micro USB TP4056 5V Micro USB Lithium Battery Charger Module features: - Based on TP4056ES regulator - Lipo micro USB Li-Ion charger - Input Voltage: 4.5V - 5.5 VDC - Full charge voltage: 4.2V +/- 1.5% - Max Output Current: 1A - Indicator LED: charging red, charging green - Operating temperature: -10ºC to + 85ºC - IN + and IN- connection for electronic circuits - Battery protection against over-discharge voltage: 2.5V - Protection against over current battery: 3A - Measurements: 25x19x5 mm - Ideal for 18650 batteries Code A0100 Available Price €0.82
20x Electrolytic Capacitor 22uF 50V 105ºC PCB for Arduino 20x Electrolytic Capacitor 22uF 50V 105ºC Arduino PCB features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 22uF-Maximum tension: 50V-Maximum temperature 105º C-Dimensions: 5x11mm-Quantity: 20 units Code D0042 Available Price €0.06
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €8.26
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.40
Raspberry Pi Zero WH 512MB RAM WIFI BLE 4.1 with soldered connector Raspberry Pi Zero is a super small computer. This version includes WIFI, Bluetooth BLE 4.1 Pi Zero is the heart of a Raspberry Pi on a small 65mm x 30mm board. With mini-HDMI, micro-B OTG USB, and the same 40-pin GPIO, it still has a great connectivity. Raspberry Pi Zero 512MB RAM WIFI BLE 4.1 with soldered connector features: - BCM2835 ARM v7 single core 1 GHz processor , - RAM memory: 512 MB, - Video: mini HDMI up to 1080p (PAL or NTSC), - Audio: only from the HDMI port, - Camera connector , - USB microB power supply, - WiFi: 2.4 GHz 802.11n, - Bluetooth 4.1 / BLE, - 40-pin GPIO, - Micro SD port . Code RA069 ✗ Out-of-Stock Price €19.42
Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg features: A compound for etching of printed circuit boards and pickling of copper. An ideal alternative to ferric chloride. It is readily soluble and does not crystallize from the solution. It etches evenly, ensures the sharpness of contours and minimizes undercutting. Usage: Dissolve the preparation in 0.5 l of water at a temperature of 50°C. Perform etching at 40°C (max. 50°C). Bath movement ensures quicker etching. The etching solution must not be stored in hermetically sealed containers due to the risk of developing overpressure and cracks. Code Q0027 Last items in stock Price €10.32
Universal developer for photo varnish and positive printed circuit boards PCB The product provides a good development quality, protecting the sharpness of the color. The formulation is free of NaOH, which significantly increases safety at work. Universal developer for photo varnish and positive printed circuit boards PCB. Code Q0094 ✗ Out-of-Stock Price €2.39
Sodium Persulfate - etching agent for PCB and copper - pack 100g Chemical substance for recording printed circuits and copper. Unlike ferric chloride, sodium persulfate is colorless, odorless, does not stain clothes and does not turn blue when it runs out. Easy to dissolve. It acts very regular with guarantee of contour sharpness. Code Q0053 Available Price €2.36
Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg Sodium Persulfate B327 (PCB) Printed Circuit Board Etching 1kg features: A compound for etching of printed circuit boards and pickling of copper. An ideal alternative to ferric chloride. It is readily soluble and does not crystallize from the solution. It etches evenly, ensures the sharpness of contours and minimizes undercutting. Usage: Dissolve the preparation in 0.5 l of water at a temperature of 50°C. Perform etching at 40°C (max. 50°C). Bath movement ensures quicker etching. The etching solution must not be stored in hermetically sealed containers due to the risk of developing overpressure and cracks. Code Q0027 Last items in stock Price €10.32
Universal developer for photo varnish and positive printed circuit boards PCB The product provides a good development quality, protecting the sharpness of the color. The formulation is free of NaOH, which significantly increases safety at work. Universal developer for photo varnish and positive printed circuit boards PCB. Code Q0094 ✗ Out-of-Stock Price €2.39
Sodium Persulfate - etching agent for PCB and copper - pack 100g Chemical substance for recording printed circuits and copper. Unlike ferric chloride, sodium persulfate is colorless, odorless, does not stain clothes and does not turn blue when it runs out. Easy to dissolve. It acts very regular with guarantee of contour sharpness. Code Q0053 Available Price €2.36