Braided Cable 3 Pin Female - Female 20cm Jumpers Dupont 2.54

40x Female-Female Cable 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont female connectors on both ends
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

Resistor 4,7K Ohm 5% 0,25W 1/4W features:
- 4.7K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 ° C to 125 ° C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
             - Vcc red
             - Yellow digital output
- Inocidable steel
- Cable length: 3m

Heater Block MK8 NTC 3950 Nozzle 0.4mm 1.75mm features:
- 3D Printer Extruder
- 0.4mm Nozzle
- 100k 3950 NTC thermistor with cable
- MK8 heater block with 12v / 40W thermal ceramic resistance with cable
- 1.75mm filament stud M6x30mm

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

High quality and very flexible heat shrink tubing. Available in different sizes (1.5mm, 2.5mm, 4mm, 6mm, 10mm and 13mm) in six colours (black, white, red, yellow, yellow, green, blue), each 10 cm long.

The module is based on a touch sensitive IC capacitive touch switch module (TTP223B).
In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features:
- Low power consumption
- Input voltage: 2 - 5.5VDC
- Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation
- 3-pin control interface:
1- GND
2- VCC
3- Control signal (output pin)
- Power indicators: Bright green LED when the sensor is on