1m filament tube 1.75mm ID 2/4mm PTFE Teflon

Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º.
An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features:
- Infrared sensor with control circuit
- Adjustable sensitivity and time
- Operating voltage: 4.5V- 20V
- Consumption in Idle state:

It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4
- Operation: 5V
- Power (max): 5-12V
- Total I / O pins: 20
- PWM pins: 5
- Analog pins: 12
- Maximum current of I / O pins: 40 mA
- Maximum current of pin 3.3V: 50 mA
- Flash memory: 32 KB (4 KB used by the bootloader)
- SRAM: 2.5 KB
- EEPROM: 1 KB
- Speed: 16 MHz
- external interrupt
- TWI / I2C, UART, SPI interfaces
- Dimensions: 18x33mm
- Weight: 30 grams

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

LCD 2004 Intelligent Reprap Controller 3D Printer can be connected directly to your RAMPS 1.4. All new operations, such as calibration, axis movement can be done only with the smart rotary encoder. You don't need to use your PC. Just use the G-Code layout stored on the SD card.

LCD display consists of a 16-character, 2-rows.
The display is compatible with the HD44780 controller
Ideal for projects with Arduino
You can use it with PIC, AVR, STM32 and many more controllers.

Indirect Extruder - Bowden style MK8 Assembly for 3D Printer I0088 features:
- This extruder is ready to mount and print
- PC4-M6 bowden pneumatic connector
- 12V 2-wire 40x40mm fan
- Metal fan cover
- MK8 heat sink
- MK8 aluminum extruder
- PAP Nema17 3.25V 1.3A motor with cable
- Capable of loading with 4.48 kg / cm

- The XL6009 module has a superior performance than the LM2577 module
- The regulator-booster of High performance
Characteristic:
- Based on the XL6009E1 regulator
- Input voltage: 3V-32V,
- Output voltage: 5-35V (adjustable),
- Output current: 2A maximum 3A (heat sink is required)
- Conversion efficiency: up to 94%
- Rectifier: not synchronous rectification
- Short circuit protection: current limitation, since recovery
- Operating temperature: industrial grade (-40 ° C - 85 ° C)
- Load regulation: ± 0.5%
- Voltage regulation: ± 0.5%
- Size: 50 x 22 x 15 mm