PLA Filamento 1.75mm 0.85kg Red color rojo
  • PLA Filamento 1.75mm 0.85kg Red color rojo
  • PLA Filamento 1.75mm 0.85kg Red color rojo

PLA Filamento 1.75mm 0.85kg Red color rojo

I0413

Premium Bobina para Impresora 3D
Fiberlogy
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Filamento de PLA, es decir, poliéster termoplástico en forma de fibra, utilizado para la impresión 3D por el método FFF y bolígrafos de impresión.
Filamento enrollado en un carrete, envasado al vacío junto con un absorbente de humedad,colocado en una caja de cartón.

Mira la video reseña del filamento:

Propiedades del filamento de PLA:

-fácil de imprimir a bajas temperaturas.
-baja contracción
-biodegradabilidad
-inodoro
-no es inflamable
-alta durabilidad,buena rigidez
-resistencia al agua completa

-viene en muchas variantes de color

Variantes de color

Parámetros de impresión de filamentos sugeridos:

Temperatura de extrusión

200°C - 230°C

Temperatura de cama caliente

50°C - 70°C*

*Cuando se utilizanadhesivo u otros medios para aumentar la adhesión, no es necesario calentar la cama.
Debido a las diferencias de diseño de las impresoras, los datos anteriores deben tratarse como pautas y los valores apropiados deben determinarse experimentalmente.

Parámetros de filamentos PLA:

Material PLA
Diámetro del filamento 1.75mm
Tolerancia ovalada +/-0.01mm
Tolerancia de diámetro +/-0.02mm
Superficie material brillo
Contracción del material muy bajo
Peso del producto 0.85 kg neto, bruto
Dimensiones de embalaje ~ 205 x 205 x 80 mm
Caja de cartón con estampado Envasado al vacío

Datos técnicos:

Propiedades materiales

Data sheet

Color
rojo
Diametro [mm]
1.75
Material
PLA
Peso [g]
850

Customers who bought this product also bought

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

P0008

Price €1.39

ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics

WIFI transceiver based on the ESP8266 controller.
It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low power mode:

W0003

Price €1.95
€17.49

14,45 tax excl.

Tax included 7
Pre-order
Do you want to receive an alert when product is back in stock?
 
We will send you an email once the product becomes available. Your email address will not be shared with anyone else.
Price €17.49

Order until 4pm we will send today
30 days return