PLA Filamento 1.75mm 0.85kg Gray color gris

TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.
Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features:
- Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument
- VCCA power supply voltage: 4.5 - 5.5 VDC
- VCCB power supply voltage: 2.7 - 3.6 VDC
- Low level input voltage V (IL): 0.8 V
- High-level input voltage V (IH): 2 V
- Low level output current I (OL): 12 - 24 mA
- High level output current I (OH): -24 - -12 mA
- 8 channels allow the conversion of the IO communication level
- Channel levels A and B are controlled by VCCA and VCCB

Cutting Pliers 130mm features:
- This model is not isolated, please use it without current
- Use to cut soft materials, electronic components, cables, plastic card
- Can also be used for welding work

Pulley GT2 16 Teeth 6mm Aluminium Pulley 3D Printer Reprap features:
- Number of teeth: 16
- Pitch: 2mm
- Material: aluminum alloy
- Outside diameter: 13mm
- Inner hole: 5mm
- Use with strap: 6mm
- Quantity: 1 unit of 16 teeth GT2 pulley, 6mm wide and 2 studs
- Ideal for fix on the axis of the motors of your 3D printer

Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA.
100% compatible UNO module.
Characteristic:
- Operating voltage: 3.3-5 VDC
- Output voltage: 0-1 VDC
- 3-pin connector:
- OUT: output signal
- VCC: Supply voltage
- GND: Ground connection - Test accuracy: ± 1UV INDEX
- Current: 0.06mA (typical), 0.1mA (maximum)
- Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds
- Operating temperature: -20ºC - + 85ºC
- Size: 19.80 x 15mm

Laminated Copper Clad Prototype PCB Circuit Board 30x19cm.

Flat Cable GPIO 40 Pins M/F features:
- For Raspberry Pi 2 and Pi 3, B and B +
- Total length 20cm
- Quantity: 1 unit

Blue 2 pole PCB mount screw terminal 5.08mm pitch Printed Circuit Board Terminal 3 poles 5.08mm pitch features:
Number of Contacts: 3
Pitch: 5.08mm
Number of Rows: 1
Mounting Type: PCB
Gender: Male
Allowable Section: 1.5mm2 (22- 14 AWG)
Termination method: screw
Type: screw terminal block
Nominal current: 16A
Nominal voltage: 250V
Color: blue
Material: Nylon 66
Depth: 10mm
Width: 7.5mm
Length: 10mm

Pulley GT2 20 Teeth 8mm Bore Aluminum 3D Printer Reprap features:
- Number of teeth: 20
- Pitch: 2mm
- Material: Aluminum alloy
- Outside diameter: 16mm
- Inner hole: 8mm
- Use with strap: 6mm and 6.35mm
- Toothed width 7mm
- Quantity: 1 unit
- Ideal for fixing on the axis of the motors of your 3D printer