Relay Module 1 Channel 5V 10A 1 Channel 5V Relay Module. This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). Relay Module 1 Channel 5V 10A features: - Channel: 1 - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - LED indicator - Dimensions: 30x 54mm Code RL005 Available Price €1.07
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €1.89
1.44 inch TFT LCD screen 128x128 SPI 1.44 inch TFT LCD screen 128x128 SPI features: - TFT LCD screen 128x128 pixels - 4-wire SPI interface (A0, SDA, SCK, CS) - Size: 1.44 inches - Interface: SPI - Resolution: 128 * 128 - Visual area: 1: 1 square - Color screen TFT, the effect is much better than other small CSTN displays - Disk drive: ST7735 - Fully compatible and alternative 5110 interface - Onboard LDO, 5V / 3.3 input voltage support V - Screen dimensions: 30 x 28 mm - PCB dimensions: 45 x 32 mm Code P0048 Available Price €5.78
LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable It has an Atmega32u4 chip running at 16Mhz with a factory-loaded bootloader. The Leonardo module has all the connectors that the Arduino Leonardo R3 and is compatible with all Arduino shields. LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable features: - ATmega32u4 microcontroller, - Operating voltage 5V, - Power (recommended) 7-12V, - Digital pins I / O 20 (of which 7 can be used as PWM outputs), - Analog input pins 12, - DC current through I / O Pin 40 mA, - DC current for pin 3.3V 50 mA, - Flash memory 32 KB (of which 4 KB are used by the bootloader), - SRAM 2.5 KB, - EEPROM 1 KB, - Clock speed 16 MHz, - Interface: UART, USB, SPI, I2C, - USB communication - Atmega32u4, Code B0004 Available Regular price €9.01 -€2.00 Price €7.01
M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features: - This sensor can be configured as auto Z axis level - Sensor detection switch inductive proximity LJ12A3-4-Z / BY - PNP DC6-36V - Often used for 3D printer bed leveling - Typical application: printer bed level sensor 3D - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - PNP NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C at + 55 ° C (Non-freezing condition) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0036 ✗ Out-of-Stock Regular price €3.30 -€0.50 Price €2.80
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Last items in stock Price €4.45
M18 Inductive Proximity Sensor M18 Inductive Proximity Sensor features: - Inductive proximity sensor detection switch LJ18A3-8-Z / BX - NPN DC6-36V - A Often used for 3D printer bed leveling - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open ) - Detecting distance 8mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition) - Head diameter 18 mm - Size 6.9 x 2cm - Cable length 90cm Code S0042 Available Price €2.88
Router TB6600 1 Axis 3.5A Stepper Motor Driver Board Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features: - Minimum operating voltage: 9 V- Maximum operating voltage: 40 V- Maximum current: ± 3.5 A- Maximum power: 160W- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23- Control inputs 5V optically isolated- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP- Current control: 0.5A/>0A/> Code I0159 Available Price €9.01
DC Circular Electromagnet 12V 2kgf 3W High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 2 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user. Code F0006 ✗ Out-of-Stock Price €7.02
Small Thrust Actuator, Solenoid - 24VDC 10mm stroke This electromagnetic push actuator allows a force of 0.8N to be exerted and has a pitch length of 10mm. It is powered by 24VDC and has a consumption of 420mA. This supply is used in industrial automation systems. Characteristic: - Input voltage: 24VDC - Thrust length: 10mm - Holding force: 0.8N - Operating temperature: -5 ° C to 40 ° C without condensation - Humidity of operating environment: 45% to 85% non-condensing - Push bar diameter: 0.8 cm / 0.3 " - Material type: Metal - Model: ZYE1-0837Z - Actuator size: 2.6x2x6.35 cm / 1.02x0.79x2.5 " Code F0004 ✗ Out-of-Stock Price €6.57
Small Thrust Actuator, Solenoid - 12VDC 10mm stroke This electromagnetic push actuator allows a force of 0.8N to be exerted and has a pitch length of 10mm. It is powered by 12VDC and has a consumption of 420mA. This supply is used in industrial automation systems. Characteristic: - Input voltage: 12VDC - Thrust length: 10mm - Holding force: 0.8N - Operating temperature: -5 ° C to 40 ° C without condensation - Humidity of operating environment: 45% to 85% non-condensing - Push bar diameter: 0.8 cm / 0.3 " - Material type: Metal - Model: ZYE1-0837Z - Actuator size: 3.7x2x2.5 cm / 1.5x0.8x1 " Code F0003 Available Price €6.57
DC Circular Electromagnet 12V 20kgf 8W High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 20 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user. Code F0005 Available Price €13.96
DC Circular Electromagnet 12V 2kgf 3W High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 2 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user. Code F0006 ✗ Out-of-Stock Price €7.02
Small Thrust Actuator, Solenoid - 24VDC 10mm stroke This electromagnetic push actuator allows a force of 0.8N to be exerted and has a pitch length of 10mm. It is powered by 24VDC and has a consumption of 420mA. This supply is used in industrial automation systems. Characteristic: - Input voltage: 24VDC - Thrust length: 10mm - Holding force: 0.8N - Operating temperature: -5 ° C to 40 ° C without condensation - Humidity of operating environment: 45% to 85% non-condensing - Push bar diameter: 0.8 cm / 0.3 " - Material type: Metal - Model: ZYE1-0837Z - Actuator size: 2.6x2x6.35 cm / 1.02x0.79x2.5 " Code F0004 ✗ Out-of-Stock Price €6.57
Small Thrust Actuator, Solenoid - 12VDC 10mm stroke This electromagnetic push actuator allows a force of 0.8N to be exerted and has a pitch length of 10mm. It is powered by 12VDC and has a consumption of 420mA. This supply is used in industrial automation systems. Characteristic: - Input voltage: 12VDC - Thrust length: 10mm - Holding force: 0.8N - Operating temperature: -5 ° C to 40 ° C without condensation - Humidity of operating environment: 45% to 85% non-condensing - Push bar diameter: 0.8 cm / 0.3 " - Material type: Metal - Model: ZYE1-0837Z - Actuator size: 3.7x2x2.5 cm / 1.5x0.8x1 " Code F0003 Available Price €6.57
DC Circular Electromagnet 12V 20kgf 8W High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 20 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user. Code F0005 Available Price €13.96