Motor Nema 17 4.28kg 17HS4401 It is one of the most popular stepper motors with 200 steps per turn and a maximum load of 4.28 kg/cm. It comes with a 1m cable. We have the best stepper motors at the best prices! Code I0020 Available Regular price €11.50 -€1.55 Price €9.95
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Price €2.49
Resettable fuse PTC 900mA 60V DC The PTC polymer fuse is a reusable element protecting the circuit against overload and short circuit. Resettable fuse PTC 900mA 60V DC features: Operation current: 900mA Maximum Voltage: 60V Temperature range: -40 „ƒ to 85 „ƒ Cured, flame retardant epoxy polymer insulating material meets UL 94V-0 requirement 40A shock current Trip current 1.8A 990mW power Min resistance 200mΩ Max. 470mΩ Dimensions A 11.7mm B 15.8mm C 5.1mm D 7.6mm E 3.1mm F 1.1mm Terminal dimensions Ø0.51x7.6mm datasheet Resettable fuse RA Code D0085 Available Price €0.96
Power supply DC 12V 16.7A 200W Power supply DC 12V 16.7A 200W features: - Supply voltage: 110 / 230V AC - Output voltage: 12V DC - Output amperage: 16.7A - Power at 12V: 200W - Dimensions: 200mm x 99mm x 43mm - IP20 ROHS CE Code A0057 Available Price €16.99
Hall Effect Sensor Module KY-003 with SH3144E TO-92 This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features: - 3-pin connector: 1- GND 2- VCC 3- Voltage is recovered depending on the magnetic effect - Supply voltage: 5VDC - Output current: 40mA Code M0131 Available Price €1.69
3A DC Converter 4-53V Adjustable LM2596H Step Down Source Wide range of voltages, improved version. Drop module. They will use a multimeter to Check the output voltage and adjust the potentiometer. 3A DC Converter 4-53V Adjustable LM2596H Step Down Source features: - Based on the LM2596HVS-ADJ regulator - Rectification: Asynchronous - Output Voltage: 3v ~ 40v DC (adjustable) - Input Voltage: 4.5v - 53v DC - Max Output Current: 3A (with heat sink) - Ripple in output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5% - Operating temperature: -40ºC to + 85ºC - Measurements: 43x 21x 14 mm Code A0018 Available Price €2.79
W5100 Mini Network Module Ethernet Shield Arduino compatible W5100 Mini Network Module Ethernet Shield Arduino features: - Shield Ethernet for Arduino and compatible boards based on the Wiznet W5100 chip - Provides a simple mode to connect your module to the local network and the internet - Compatible with the official Arduino Ethernet library - With this shield you can build a web server - It can be used as a server or as a client - Controller: Wiznet W5100 - Supports TCP and UDP protocols - Supports up to 4 simultaneous connections - Compatible with all versions of Arduino: UNO, mega 1280/2560 - Dimensions: 50 x 25x 25mm Code W0074 Available Price €10.90
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
Small Thrust Actuator, Solenoid - 24VDC 10mm stroke This electromagnetic push actuator allows a force of 0.8N to be exerted and has a pitch length of 10mm. It is powered by 24VDC and has a consumption of 420mA. This supply is used in industrial automation systems. Characteristic: - Input voltage: 24VDC - Thrust length: 10mm - Holding force: 0.8N - Operating temperature: -5 ° C to 40 ° C without condensation - Humidity of operating environment: 45% to 85% non-condensing - Push bar diameter: 0.8 cm / 0.3 " - Material type: Metal - Model: ZYE1-0837Z - Actuator size: 2.6x2x6.35 cm / 1.02x0.79x2.5 " Code F0004 Available Price €7.95
DC Circular Electromagnet 12V 20kgf 8W High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 20 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user. Code F0005 Available Price €16.89
DC Circular Electromagnet 12V 2kgf 3W High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 2 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user. Code F0006 Available Price €8.49
Electric Door Lock 12V DC Electromagnetic Solenoid Easy to install for the electric door lock or other automatic door lock systems with the mounting board. Code M0218 Available Regular price €9.95 -€1.00 Price €8.95
Small Thrust Actuator, Solenoid - 24VDC 10mm stroke This electromagnetic push actuator allows a force of 0.8N to be exerted and has a pitch length of 10mm. It is powered by 24VDC and has a consumption of 420mA. This supply is used in industrial automation systems. Characteristic: - Input voltage: 24VDC - Thrust length: 10mm - Holding force: 0.8N - Operating temperature: -5 ° C to 40 ° C without condensation - Humidity of operating environment: 45% to 85% non-condensing - Push bar diameter: 0.8 cm / 0.3 " - Material type: Metal - Model: ZYE1-0837Z - Actuator size: 2.6x2x6.35 cm / 1.02x0.79x2.5 " Code F0004 Available Price €7.95
DC Circular Electromagnet 12V 20kgf 8W High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 20 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user. Code F0005 Available Price €16.89
DC Circular Electromagnet 12V 2kgf 3W High quality clamping electromagnet. Its supply voltage is 12V. The lifting capacity of up to 2 kg. The temperature limit reaches 130 degrees centigrade. Retention electromagnets are most often used for electric / magnetic locking of doors, flaps, and others. Use metal plates with a thickness starting from 3mm, this will ensure maximum retention force on the locking element. It is important to remove heat from the housing. The maximum force decreases as the coil temperature increases. This electromagnet will meet the expectations of even the most demanding user. Code F0006 Available Price €8.49
Electric Door Lock 12V DC Electromagnetic Solenoid Easy to install for the electric door lock or other automatic door lock systems with the mounting board. Code M0218 Available Regular price €9.95 -€1.00 Price €8.95