Ramps 1.5 Reprap - Arduino Mega Pololu Shield

The output current of this controller is infinitely adjustable to meet the various requirements of your application.
It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.
Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.
Its large heat sink allows good quality cooling.
The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features:
  - Operating voltage DC 10V-45V
- Maximum nominal output: 4.5 A
- DC32V switching power is recommended
- 6N137 high speed optical coupling, ensure high speed without losing step

5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features:
- Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software.
- Designed for single axis CNC single phase stepper controller controller:
M542, MA860H, 2M542, DM860 etc.
- Stepper motor controller drivers 5 axis maximum support.
- Wide input voltage range: 12-24V and with anti-reverse function.
- USB power supply and peripheral power phase are separated to protect computer security
- All signals are opto-isolated, which can protect the security of your computer.
- 5 input interface to define limit, emergency stop, cutter alignment, etc.
- A relay output control interface, accessed by spindle motor or air pump, water pump, etc.

Zum Scanner Expansion Board 3D DIY features:
- Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- 3D Scanner Ciclop is an open source project created by bq
- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser
- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board

The DM556 low-voltage digital stepper motor controller, which uses the latest 32-bit DSP technology, is suitable for driving the 57 and 86 series motors Nema23, with excellent low-speed performance to meet the application needs of small and medium-sized equipment.

Stepstick A4988 controller
Driver for stepper motors
Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield
A4988 + Stepstick Radiator Stepper Motor Reprap features:

- Minimum operating voltage: 8 V
- Operating voltage maximum: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm

MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply.

Optical Limit Switch for 3D CNC Printer RepRap Prusa Ramps 1.4 features:
- 100% brand new and high quality
- Optical detector: TCST2103
- Length cable: 50cm
- Size: 32mm x 10mm

Feature of 3D Zum shield: - Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- Content:
       - 1x Zum Shield 3D
       - 1x UNO R3 Compatible Arduino
       - 1x Controller A4988
       - 1x Male pin strip
       - 1x Heatsink for A4988
       - 1x USB cable
       - Jumpers

Mechanical End of Career CNC Ramps1.4 3D Printer features:
- Mechanical limit switch, Endstop
- 100% brand new and high quality
- 1A 125V AC switch - Cable length: 70cm
- PCB dimensions: 40mm x 15mm

The kit contains the Mega board, the Ramps 1.4 shield and 4 A4988 controllers with heatsinks.