150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car A high-performance voltage regulator-riser 12V laptop power supply car accumulator150W Boost Converter Voltage Regulator Module DC Voltage 12V-35 Car features:- Input voltage: 10V-32V- Output voltage: 12-35V (adjustable)- Output current: 6A maximum- Input current: 10A maximum- Output power: 100W of natural cooling (MAX), plus 150W (MAX) fan- Conversion efficiency: up to 94% (2.5 A 16V Input Output 19V when measured - only as a reference)- Wiring: seamless terminal- Operating temperature: industrial grade (-40 „ƒ to 85 „ƒ) (room temperature exceeds 40 degrees, use of lower power, or add fan)- Current without load: 25 mA typical Code A0006 Available Price €4.99
DHT11 Temperature and Humidity Sensor The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features: - Operating voltage: 3 to 5 VDC- Humidity measurement range: 20-95% ± 5% accuracy- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy- Maximum sampling rate: 2 seconds- Working current 2.5mA- Iterfaz 1-wire- Dimensions: 2.3 x1.2x 0.5cm- Quantity: 1 unit Code S0010 Available Price €2.49
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.95 -€0.50 Price €2.45
3S BMS 25A 12.6V 18650 PCM PCB Circuit Charging Module. In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0106 Available Price €4.49
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.99
Prototype Board MB102 Protoboard 830 points for Arduino Prototype Board MB-102 Protoboard 830 points Arduino features: - 830 Connections - Linkable with other boards - Base with adhesive to attach it to the work surface - Measures 165x 55x8mm Code PB004 Available Regular price €2.99 -€0.50 Price €2.49
40x Female-Female Cable 20cm 40x Female-Female Cable 20cm features: -Length: 20cm -Quantity: 40 wires -Dupont female connectors on both ends -Compatible with 2.54mm male connectors -High quality and good working condition -Easy to install and use Code K0004 Available Price €2.49
Mini VNH3SP30 Stepper Motor Driver Module 30A Mini VNH3SP30 Stepper Motor Driver Modules capable of handling a high consumption motor. Code R0020 ✗ Out-of-Stock Price €4.85
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.95
Kit Mega 2560 R3 + Ramps 1.4 RepRap + 4x A4988 The kit contains the Mega board, the Ramps 1.4 shield and 4 A4988 controllers with heatsinks. Code I0022 Backorder Regular price €38.94 -€4.88 Price €34.06
5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine 5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features: - Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software. - Designed for single axis CNC single phase stepper controller controller: M542, MA860H, 2M542, DM860 etc. - Stepper motor controller drivers 5 axis maximum support. - Wide input voltage range: 12-24V and with anti-reverse function. - USB power supply and peripheral power phase are separated to protect computer security - All signals are opto-isolated, which can protect the security of your computer. - 5 input interface to define limit, emergency stop, cutter alignment, etc. - A relay output control interface, accessed by spindle motor or air pump, water pump, etc. Code I0124 Available Price €9.49
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €3.49
CNC Shield Expansion Plate + 4x A4988 Stepstick 3D Printer A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details. Code I0105 Available Price €10.35
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €5.99
Zum Scanner Expansion Board 3D DIY Zum Scanner Expansion Board 3D DIY features: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- 3D Scanner Ciclop is an open source project created by bq- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board Code I0056 Available Price €12.49
MKS PWC V3.0 power auto-off while finish printing module Auto shut down module for MKS GEN L SKR V1.3 MKS PWC automatically turning off after the printing. It helps in the cases like the unexpected power off or you have to leave during the printing, and other similar issues. Code I0187 Available Regular price €17.49 -€4.00 Price €13.49
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.75
Mechanical Ender 3 / 5 / CR 10 / 20 X Pro 3D Printer Mechanical Ender 3 5 CR 10 20 X Pro 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Compatible with Ender-3 series, CR-10 series, etc. - PCB dimensions: 18mm x 18mm Code I0178 Available Price €3.75
Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.95
Kit Mega 2560 R3 + Ramps 1.4 RepRap + 4x A4988 The kit contains the Mega board, the Ramps 1.4 shield and 4 A4988 controllers with heatsinks. Code I0022 Backorder Regular price €38.94 -€4.88 Price €34.06
5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine 5 Axis CNC Interface Board Stepper Driver Mach3 USB CNC Cutting Machine features: - Compatible with MACH3, Linux CNC (EMC2) etc. CNC parallel control software. - Designed for single axis CNC single phase stepper controller controller: M542, MA860H, 2M542, DM860 etc. - Stepper motor controller drivers 5 axis maximum support. - Wide input voltage range: 12-24V and with anti-reverse function. - USB power supply and peripheral power phase are separated to protect computer security - All signals are opto-isolated, which can protect the security of your computer. - 5 input interface to define limit, emergency stop, cutter alignment, etc. - A relay output control interface, accessed by spindle motor or air pump, water pump, etc. Code I0124 Available Price €9.49
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €3.49
CNC Shield Expansion Plate + 4x A4988 Stepstick 3D Printer A CNC expansion board kit and 4 stepsticks A4988 for 3D printer. See each component in the product description for details. Code I0105 Available Price €10.35
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €5.99
Zum Scanner Expansion Board 3D DIY Zum Scanner Expansion Board 3D DIY features: - Input voltage 8-16 V- 2 connectors for stepper motors- 4 connectors for laser- Analog connectors for LDR sensors- Power jack connector- Reset button- Protection fuse for stepper motors- Compatible with Arduino UNO- Dimensions of PCB 67 x 54 mm- 3D Scanner Ciclop is an open source project created by bq- Zum shield DIY 3D scanner, which used to control the stepper motors, the LDR sensor and the laser- The complete electronic package that includes a ZUM Scan Shield, an A4988 Stepper Driver and an Arduino UNO R3 Board Code I0056 Available Price €12.49
MKS PWC V3.0 power auto-off while finish printing module Auto shut down module for MKS GEN L SKR V1.3 MKS PWC automatically turning off after the printing. It helps in the cases like the unexpected power off or you have to leave during the printing, and other similar issues. Code I0187 Available Regular price €17.49 -€4.00 Price €13.49
CNC Shield Expansion Plate V3 Engraver 3D Printer CNC shield for arduino works as a controller for CNC type milling machines, 3D printers, laser cutters . CNC Shield Expansion Plate V3 Engraver 3D Printer features: 4 compatible sockets for use of A4988 stepper motor controllers (PAP), DRV8825, other compatible 4 support axes X, Y, Z, A 2 limit switches for each axis (6 in total) Code I0011 Available Price €2.75
Mechanical Ender 3 / 5 / CR 10 / 20 X Pro 3D Printer Mechanical Ender 3 5 CR 10 20 X Pro 3D Printer features: - Mechanical limit switch, Endstop - 100% brand new and high quality - 1A 125V AC switch - Compatible with Ender-3 series, CR-10 series, etc. - PCB dimensions: 18mm x 18mm Code I0178 Available Price €3.75