Ramps 1.4 Reprap - Arduino Mega Pololu Shield

CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features:
- Content:
* 1x UNO R3 CH340 Compatible with Arduino
* 1x CNC Shield V3
* 4x A4988 Drivers
* 4x Heatsinks for A4988
* Jumpers

RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers.

RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825.

Feature of 3D Zum shield: - Input voltage 8-16 V
- 2 connectors for stepper motors
- 4 connectors for laser
- Analog connectors for LDR sensors
- Power jack connector
- Reset button
- Protection fuse for stepper motors
- Compatible with Arduino UNO
- Dimensions of PCB 67 x 54 mm
- Content:
       - 1x Zum Shield 3D
       - 1x UNO R3 Compatible Arduino
       - 1x Controller A4988
       - 1x Male pin strip
       - 1x Heatsink for A4988
       - 1x USB cable
       - Jumpers

Stepper Motor Driver Board for industrial automation, Robotics, CNC Engraving machines, CNC 3D printer, CNC embroidery machines, laser engraving, labeling machines, X-Y Table, Pick and Place robot/machine, CNC drilling milling machine and many more application.
Run easily with Arduino. Router TB6600 1 Axis 3.5A Stepper Motor Driver Board features:
- Minimum operating voltage: 9 V
- Maximum operating voltage: 40 V
- Maximum current: ± 3.5 A
- Maximum power: 160W
- Suitable for stepper motors NEMA16, NEMA17 and NEMA 23
- Control inputs 5V optically isolated
- Step resolution: 200, 400, 400, 800, 1600, 3200, 6400
- Resolution of microsteps: full, 1/2A, 1/2B, 1/4, 1/8, 1/16 y 1/32 adjustable by interruptor DIP
- Current control: 0.5A/>0A/>

The kit contains the Mega board, the Ramps 1.4 shield and 4 A4988 controllers with heatsinks.

The DM556 low-voltage digital stepper motor controller, which uses the latest 32-bit DSP technology, is suitable for driving the 57 and 86 series motors Nema23, with excellent low-speed performance to meet the application needs of small and medium-sized equipment.

The controller creates step-by-step motor control functions preset with the latest imported high-speed chip and uses a combination of software and hardware methods to ensure superior anti-jam performance of the controller.
It also has reverse polarity protection, overvoltage protection, overcurrent protection, absolute guarantee of safe operation of the controller in a variety of hostile factory environments.
Applies to stepper motor control switches, round-trip motion control, fixed speed control. Industrial DKC-1A stepper motor controller features:
- Operating voltage: 5-32 VDC
- Signal entry point for the lower level entry
- Optimization of the acceleration of the S curve
- The maximum output frequency can reach 20 KHz

TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink

Compared to the TMC2100 module, the TMC2208 controller module emits less heat.

The output current of this controller is infinitely adjustable to meet the various requirements of your application.
It has an automatic half-current function and a semi-automatic flow switch is also available, easy to use.
Its 6N137 high speed optical coupling ensures high speed without losing step printed on the rear panel subdividing the configuration instructions.
Its large heat sink allows good quality cooling.
The output is protected against short circuits. TB6600 4.5A Single Axis CNC Controller features:
  - Operating voltage DC 10V-45V
- Maximum nominal output: 4.5 A
- DC32V switching power is recommended
- 6N137 high speed optical coupling, ensure high speed without losing step

A4988 + RepRap Radiator features:
- Minimum operating voltage: 8 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A (adequately ventilated or refrigerated)
- Logic voltage: 3 V / 5.5V
- Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16
- Factory soldered temples
- Use potentiometer to adjust current
- Measurements: 20x16x12 mm