50cm HDMI V1.3 Male to Raspberry PI 1080P Gold Silver
  • 50cm HDMI V1.3 Male to Raspberry PI 1080P Gold Silver

50cm HDMI V1.3 Male to Raspberry PI 1080P Gold Silver

RA009

50cm HDMI V1.3 Male to Raspberry PI 1080P Gold Silver features:
- For Raspberry Pi 2 and Pi 3, B and B +
- HDMI V1.3b cable and full 1080P (category 2) resolution
- Type A male at both ends
- High quality gold shielded connectors
- Manufactured with high quality copper conductors (OFC-Oxygen Free Copper- 99.99%) that guarantees the highest transmission quality
- Refresh rates up to 120Hz
- Length: 50cm
- Quantity: 1 unit

Raspberry Pi
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

50cm HDMI V1.3 Male to Raspberry PI 1080P Gold Silver features:

- For Raspberry Pi 2 and Pi 3, B and B +
- HDMI V1.3b cable and full 1080P (category 2) resolution
- Type A male at both ends
- High quality gold shielded connectors
- Manufactured with high quality copper conductors (OFC-Oxygen Free Copper- 99.99%) that guarantees the highest transmission quality
- Refresh rates up to 120Hz
- Length: 50cm
- Quantity: 1 unit

Data sheet

Longitud de cable
50cm

Customers who bought this product also bought

2 Channel Relay Module 5V 10A for Arduino

2 Channel Relay Module 5V 10A for Arduino features:
- 5V relay module with 2 optocoupled channels
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- LED indicator: For each channel
- Dimensions: 40x 50mm

RL006

Regular price €1.64 -€0.35 Price €1.29

ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

W0014

Price €4.09

Buzzer 5V Active Buzzer 4 to 7V DC

Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects.
Buzzer 5V Active Buzzer 4 to 7V DC features:

- Input voltage: 4V to 7V
- Diameter: 12mm
- Height: 9.5mm
- Spacing Pins: 7.6mm
- Maximum Current:

M0007

Price €0.37

NE555P DIP8 Precision Timer Integrated Circuit

NE555P DIP8 Precision Timer Integrated Circuit features:
- Blister: DIP8
- Number of pins: 8
- Step between pins: 2.54 mm
- Manufacturer: Texas Instrument - Input voltage VCC: 4.5 - 16 VDC
- THRES voltage level: 2.4 - 11.2 VDC
- TRIG voltage level: 1.1 - 5.6 VDC
- RESET voltage level: 0.3 - 1 VDC
- DISCH voltage level change out of state: 0.15 - 0.4 nA
- CONT voltage (open circuit): 2.6 - 11 VDC
- Low level output voltage: 0.1 - 0.4 V
- High level output voltage: 2.75 - 13.3 V - Output current I (O): ± 200 mA
- THRES current: 30 - 250 nA
- TRIG current: 0.5 - 2 μA
- RESET current: -0.4 - 0.4 μA
- Current change DISCH out of state: 20 - 100 nA

T0061

Price €0.65

Photoresistor GL5516 LDR

10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.
Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features:
- Model: GL5516
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 90mW.
- Resistance with light (10lux): 5-10KΩ
- Resistance with darkness (0lux): 0.5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

S0012

Price €0.12

CP2102 USB 2.0 A RS232 Converter UART TTL Serial

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

C0001

Price €3.06
€1.40

1,40 tax excl.

1
30+ items
Price €1.40

Order until 4pm we will send today
30 days return