Quartz Crystal Oscillator 20 MHz

Descent module.
Use a multimeter to check the output voltage and adjust the potentiometer.
Control of tension.
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:
- Input voltage: 4.5-38V
- Output voltage: 1.25-36.5V
- Current output: 2A (max 3A with heat sink)
- Operating temperature: -40 to + 85 ºC
- Operating frequency: 150KHz
- Efficiency conversion: up to 92%
- Load Regulation: +/- 0.5%
- Voltage Regulation: +/- 2.5%
- Protection over temperature: the output switches off automatically
- Size: 62mm x 38mm x 15mm
Principal functions:
- Step-down converter with overcurrent protection
- Voltmeter up to 40V, remember to set the input voltage to 4.5V

Characteristic: -Length: 20cm
-Quantity: 40 cables
-Mono Dupont connectors on both ends
-Compatible with 2.54mm female connectors
-High quality and good working condition
-Easy to install and use

Ceramic Capacitor 10nF 50v 103 PCB PIC Arduino 0.01uF features:

Orders only in multiples of 20 units
-Type: Ceramic Y5V
-Tolerance: +/-20%
-Dimensions: diameter 6mm, pitch 5.08mm

Resistor 330K Ohm 5% 0,25W 1/4W features:
-330 Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

WIFI transceiver based on the ESP8266 controller.
It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low power mode:

SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features:
Flux liquid alcohol-based for electronic welding.
Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive
Form: liquid
Capacity: 50ml
Content of solid bodies: 0 ... 5%
Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.
It cleans easily with alcohol.
It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.
- Keep the boat tightly closed and far away from the children.
- Use in ventilated spaces.

Totally new and of high quality.
Dissipate the heat of the computer by refrigerating it effectively.
It is used to attach passive dissipaters to graphic memories and chip plates and LED diodes.
Make sure to put the components correctly, once it has dried it will not be able to detach. Adhesive Thermal Paste Glue 10g CPU features:
  - Color white
- Surface drying time [25 ° C, min]: 2- 8
- Hardness: 45 -75
- Tensile strenght (Mpa): 2.0
- Elongation (%): 100
- Thermal Conductivity W / mk:> 1,0
- Volume Resistance (c-in / W): <2.0 x 10 * 15
- Dielectric strength (KV / mm): 20
- Dielectric Constant: 3.0
- Dielectric loss factor (60Hz): 0.003
- Operating temperature (max): 200 ° C

Resistor 10K Ohm 5% 0,25W 1/4W features:
-10K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm