FT232 USB to TTL Serial Converter Adapter Module 5V 3.3V + Cable

40x Female-Female Cable 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont female connectors on both ends
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

It has an ON / OFF switch that will cut off power when you don't need it.
USB to Micro USB On/Off Switch Arduino Charger Cable features:
- Black color
- Length: 150cm
- Maximum current 1A

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

SIM800L GPRS GSM SIM Board Quadband features:
Package includes:
- SIM800L module,
- 2x pin headers,
- Spring antenna,
- 3G PCB antenna - 15cm cable.
- Supported SIM format: Micro SIM.

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

This product is widely used in radio modifications, cell phone flash, xbox360 flash detection, GPS, car, Flash, HDD repair, top box upgrade.
It can be used to download MCU types. Module MAX3232 Converter RS232 to TTL Port DB9 female features:
- Input voltage: 3.3 - 5 VDC
- Multi-channel RS232 controller / receiver MAX3232
- Transmission / reception speed up to 250 kbit / s
- DB9 serial port
- Interface with four pins:
       - TX: transmission signal
       - RX: reception signal
       - VCC: Supply voltage
       - GND: connects the power cathode
- Operating temperature: -65 ° C - + 150 ° C
- UART communication
- Includes a 4-wire female / female connector for easy connection with the arduino

Descripción:
El adaptador de HDMI a VGA le permite conectar un monitor, proyector o LCD analógico estándar que usa un conector o cable VGA a un cuaderno, DVD, TVbox, reproductor BIU-rog, computadora, proyector.
Característica:
- Tipo: adaptador/convertidor AV,
- Conector A: HDMI macho,
- Conector B: VGA hembra,
- Conexión Split / Duplicación: ninguna (1: 1),
- El adaptador dispone de una entrada audio Jack hembra,
- Ancho del cable del adaptador: 15cm,
- Incluye un cable audio Jack macho de ambos lados,
- Ancho del cable audio: 52cm,
- Color: blanco.

TTL level conversion module 5V 3.3V IO Single Interchange Compatible I2C SPI.
Use of high-speed dual-level IT supply level translator chip design. TTL Level Converter 5V - 3.3V IO LJ245A features:
- Main chip: Octal bus transceiver and change from 3.3-V to 5-V with outputs of 3 states LJ245A of Texas Instrument
- VCCA power supply voltage: 4.5 - 5.5 VDC
- VCCB power supply voltage: 2.7 - 3.6 VDC
- Low level input voltage V (IL): 0.8 V
- High-level input voltage V (IH): 2 V
- Low level output current I (OL): 12 - 24 mA
- High level output current I (OH): -24 - -12 mA
- 8 channels allow the conversion of the IO communication level
- Channel levels A and B are controlled by VCCA and VCCB

6-pin/10-pin Kanda DIL adapter features:
- Connector for Usbasp Programmer AVR Atmega8 Atmega128

Ideal for connecting TTL RS232 devices to your PC through the USB port. PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin features:
- Compatible controller PL2303HXA
- 4 pins: 5.0V (red), TxR (green), RxD (white), GND (black)
- 2.5A self-recovery protective fuse
- Supported OS: Win8, Win10, WinME, Win2003, Win XP, Vista, Win 7 The 64-bit Prolific drivers provided by Microsoft through Windows Update will not work with most adapters and will therefore generate the generic "Code 10" error.

With KANDA adapter it is ideal for projects with ARDUINO. Characteristic: - AVR 5V / 3.3V microcontrollers - programming voltage change through jumper JP1
- Status LED indicators
- Transmission speed: 5kB / s
- Protective fuse of possible damage to the USB port
- Supported OS: Win ME, Win XP, Vista, Win 7, Win8, Linux
- Works with Bascom, Eclipse, WINAVR, avrDUDE, ARDUINO IDE, ATMEL STUDIO The programmer is compatible with most AVR Atmel processors: - MEGA series 8,16,32,64,218 € ¦
- Tiny series: ATtiny10, ATtiny11, ATtiny12, ATtiny13, ATtiny13A, ATtiny € 15 ¦
- CAN series: AT90CAN32, AT90CAN64, AT90CAN128 € ¦
- AT90S2313 series, AT90S2323, AT90S144, AT90S1434 ¦

Ideal for connecting RS485 devices to your PC through the USB port. USB to RS485 USB to 485 Max485 Converter features:
- CH340 controller
- Supported OS: Win XP, Vista, Win 7.8, OS, Linux
- Work with Modbus, Profibus
- USB 2.0 specification with 6Mbps of maximum speed
- Measures: 60x 18x 14 mm

This module equipped with a PCF8591 converter has a low current power supply and includes 8 bit CMOS data acquisition devices.
Your converter has four analog inputs, one analog output and one I2C serial bus interface.
It is supplied in the voltage range 2.5V-6V, analog voltage between the negative potential VSS and positive VDD. The control and data signals are transmitted on the two-wire I2C bi-directional bus to the transformed series.
The intensity of the ambient light can be converted into a digital signal thanks to its integrated photoresistor.
It allows access to eight PCF8591 converters on the same I2C bus without additional equipment. Converter Module AD-DA PCF8591 - Analog Voltage 2.5V-6V features:
- Supply voltage (between VSS and VDD): 2.5-6VDC

A standard IEEE1284 DB25 parallel port to your PC via the USB port. Transmission speed reaches 12 Mbps. This cable is "USB Printing Support" port and not Parallel "LPT Printer Port"