USBASP AVR ATmega8 ATmega128 Programmer Kanda Adapter Cable

3.3V/5V I2C logic level converter module with soldering pins.
Ideal to connect a device that works at 3.3V to one that works with 5V.
It works with digital signals (high and low levels).
Logic Level Converter 3.3 / 5V I2C IIC features:
- Voltage: 3.3V/5V
- Measures: 1.5x 1 cm

Descripción:
El adaptador de HDMI a VGA le permite conectar un monitor, proyector o LCD analógico estándar que usa un conector o cable VGA a un cuaderno, DVD, TVbox, reproductor BIU-rog, computadora, proyector.
Característica:
- Tipo: adaptador/convertidor AV,
- Conector A: HDMI macho,
- Conector B: VGA hembra,
- Conexión Split / Duplicación: ninguna (1: 1),
- El adaptador dispone de una entrada audio Jack hembra,
- Ancho del cable del adaptador: 15cm,
- Incluye un cable audio Jack macho de ambos lados,
- Ancho del cable audio: 52cm,
- Color: blanco.

This bidirectional logic level converter can be used with normal series, I2C, SPI and other digital signals. It does not work with an analog signal.
It is very easy to use. The card must be powered from the two voltages (high and low voltage) used by the system.
A high voltage (5 V for example) to the pin "HV", low voltage (3.3 V for example) in "LV", and the system ground to pin "GND". TTL Converter Module 5V - 3.3V Bidirectional 2 Channel I2C Logic Level features:
- 2 high voltage channels and low voltage logic logic for bidirectional translation
- 2 low voltage channels High voltage high voltage logic in unidirectional conversion
- The board module is compatible, it can be inserted directly in the use test panel
- HV to 5 V power

A multiplexer of this type actually only acts as a switch 16 to a 1.
The 4 digital pins are used to set high or low, (binary Y0-Y15) to determine which input pin is connected to pin "Z".
The control input S0-S3 is set to low "logic level 0", the signal C0 is connected to the output Z. Multiplexer 16 Channels CD74HC4067 MUX/DEMUX features:
- Based on chip CD74HC4067
- Analog signal input: Y0-Y15, 16 channels
- Analog signal output: Z pin
- Digital input, channel control: S0-S3
- Module size: approx. 4 x 1.8cm
- Package includes:
* 1 x CD74HC4067 MUX connection module
* 2 x row of soldering pins

The PCF8591 is a low-power 8-bit single-chip, single-chip, 8-bit data acquisition device with four analog inputs, an analog output, and an I2C serial bus interface.
Three address legs A0, A1 and A2 are used to program the hardware address, allowing the use of up to eight devices connected to the I2C bus without additional hardware.
Address, control and data to and from the device are transferred in series through the two-way bidirectional I2C bus. Analogue to Digital Converter PCF8591T features:
- Main chip: PCF85911
- Operating voltage supply: 2.5 - 6 V
- Low standby current
- Serial input / output through the I2C bus
- 3 hardware address pins A0, A1, A2
- Sampling speed given by the I2C bus speed

This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards.

Converter Module RS485 a Transceiver TTL 485 Max485 5V PLC features:
- Working voltage and TTL levels: 5V
- Size: 44 x 14 mm

Ideal for connecting TTL RS232 devices to your PC through the USB port. CP2102 USB 2.0 A RS232 Converter UART TTL Serial features:
- Controller CP2102
- 5 pins: 3.3v, 5.0v, TxR, RxD, GND
- Standard USB type to male and 5 pin TTL connector
- 3 Status LEDs: Power, RX and TX
- USB 2.0 specification with 12Mbps maximum speed

Ideal for connecting TTL RS232 devices to your PC through the USB port. PL2303HX PL2303 USB to UART TTL Cable Module RS232 Converter 4 Pin features:
- Compatible controller PL2303HXA
- 4 pins: 5.0V (red), TxR (green), RxD (white), GND (black)
- 2.5A self-recovery protective fuse
- Supported OS: Win8, Win10, WinME, Win2003, Win XP, Vista, Win 7 The 64-bit Prolific drivers provided by Microsoft through Windows Update will not work with most adapters and will therefore generate the generic "Code 10" error.

6-pin/10-pin Kanda DIL adapter features:
- Connector for Usbasp Programmer AVR Atmega8 Atmega128