LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.39
20x Electrolytic Capacitor 22uF 50V 105ºC PCB for Arduino 20x Electrolytic Capacitor 22uF 50V 105ºC Arduino PCB features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 22uF-Maximum tension: 50V-Maximum temperature 105º C-Dimensions: 5x11mm-Quantity: 20 units Code D0042 Available Price €0.07
28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:- Stepper motor 28BYJ-48 + ULN2003 controller- The 28BYJ-48 has everything you need to start using motors step by step in your project- A stepper motor converts digital impulses into small steps of movement in one direction- The motor also comes with a ULN2003 motor controller card- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA- Equipped with state indicator LEDs A, B, C, D- Engine model: 28BYJ-48- Phasing Engine: 4- Operating voltage: 12V DC- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 Ohm- Angle per step: 5,625º- Steps per round: 64 Code R0036 Backorder Price €2.95
Tower Pro Micro Servo 9g SG90 360 degree Tower Pro Micro Servo 9g SG90 360 degree features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0075 Available Price €2.95
Black Crocodile Clip KK1 with Banana Plug It is used to pass the current, power electrical and electronic circuits, fans, motors, among others. Black Crocodile Clip KK1 with Banana Plug features: - Total length: 53 mm- Handle length: 34 mm- Color: Black- Banana shot: yes- Isolated terminals: yes- Maximum opening: Around 9 mm- Conductive material: Nickel-plated steel- Includes 1 unit Code K0131 Available Price €0.79
Capacitive Touch Sensor Module TTP229 - 16 Touch Sensitive Pads This capacitive touch sensor module uses the TTP229 integrated circuit, making it easy to add capacitive touch input to your project . Capacitive Touch Sensor Module TTP229 - 16 Touch Sensitive Pads features: 16 responsive touch pads that make an ideal replacement for older keyboards. Capacitive Touch Sensor Module TTP229 - 16 Touch Sensitive Pads features: - Capacitive touch sensor 16-key TTP229 built into the dash, - On-board power LED indicator, - Working voltage range: 2.4 - 5.5 VDC, - Configurable output mode, - PCB size: 49.3 x 64.5 mm. Code M0190 Available Price €5.20
Double Side Prototype Board PCB 8x12cm Double Side Prototype Board PCB 8x12cm features: -Thickness of PCB: 1.6mm-Material: high quality FR-4 glass fiber PCB-Presented and numbered on both sides-Top and bottom are identical copper layers-Pads grid (pitch) 2.54mm/0.1", hole diameter 0.9mm Code PB018 Available Price €2.69
Thermal tape 20mm type Kapton Characteristic: - Supports up to 280ºC - Electrical and antistatic insulation - Resistant to acidic products and alkaline - Solvent resistant - Adhesive - Length Approx: 26m Code I0053 Available Price €4.85
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.45
Micro USB Interface Power Supply DC 7-12 VDC This module is a 2-channel DC 7-12 VDC power supply for MB102 breadboards. Each channel has its switch for configure the output voltage to 3.3V or 5V. Its 3x2 male connectors allow it to be connected to the breadboard in a very simple way without soldering. Micro USB Interface Power Supply DC 7-12 VDC features: - Operating voltage: DC 7-12 V - Power display LED - 1 Jack Female connector 2.1 mm to supply - 1 AMS1117 3.3V regulator - 1 AMS1117 5V regulator - 4 3x2 connectors - 1 5V micro USB female outlet - Size: 5.5x3.5x1.5 cm Code A0078 Available Price €9.50
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.49
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €5.49
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.99
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €3.49
10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V This power supply delivers an output voltage lower than that of the input and allows power loads up to 10A. It has its heat sink, it is Recommended to use it for loads up to 8A for optimal cooling. Includes its foot protection kit, which greatly facilitates heat dissipation and use. 10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V features: - Input voltage: DC 8V-40V - Output voltage: DC 1.25V-36V adjustable with potentiometer (can only be used as a reducing module, the input must be higher than 1.25V output) - Output current: 8A (Max 10A for a short time), adjustable with potentiometer. Below 5A it can cool naturally - Output power: Max 150W - Key components: - Electrolytic capacitors 470µF - 50V Code A0074 Available Price €13.49
Boost Adjustable Power Converter LM2587 5A DC 4.5-35V A high-performance step-up regulator Boost Adjustable Power Converter LM2587 5A DC 4.5-35V features: - Input voltage: 3.5 ~ 32v - Output voltage: 4.5 ~ 35v (adjustable) - Output current: 3A, maximum 5A (heatsink heat is required) - Conversion efficiency: up to 90% - Operating frequency: 100KHz - Short circuit protection: current limiting - Operating temperature: industrial grade (- 40 to 85) - PCB dimensions: 52 x 37 mm Code A0019 Available Price €6.99
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €5.95
XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.45
Micro USB Interface Power Supply DC 7-12 VDC This module is a 2-channel DC 7-12 VDC power supply for MB102 breadboards. Each channel has its switch for configure the output voltage to 3.3V or 5V. Its 3x2 male connectors allow it to be connected to the breadboard in a very simple way without soldering. Micro USB Interface Power Supply DC 7-12 VDC features: - Operating voltage: DC 7-12 V - Power display LED - 1 Jack Female connector 2.1 mm to supply - 1 AMS1117 3.3V regulator - 1 AMS1117 5V regulator - 4 3x2 connectors - 1 5V micro USB female outlet - Size: 5.5x3.5x1.5 cm Code A0078 Available Price €9.50
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.49
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.99
5V supply module with 2A step up output DM13 Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A. Works with frequency signals up to 1.2 MHz. Characteristic: - Input voltage range: 2 - 5 VDC, - Fixed output voltage: 5 VDC, - Output accuracy: ± 0.1 V, - Maximum output current: 2A, - Ripple at full load: Vpp & lt; 70mV, - Operating temperatures: -40ºC - + 85ºC, - PCB size: 17x13mm. Code A0092 Available Price €5.49
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.99
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €3.49
10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V This power supply delivers an output voltage lower than that of the input and allows power loads up to 10A. It has its heat sink, it is Recommended to use it for loads up to 8A for optimal cooling. Includes its foot protection kit, which greatly facilitates heat dissipation and use. 10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V features: - Input voltage: DC 8V-40V - Output voltage: DC 1.25V-36V adjustable with potentiometer (can only be used as a reducing module, the input must be higher than 1.25V output) - Output current: 8A (Max 10A for a short time), adjustable with potentiometer. Below 5A it can cool naturally - Output power: Max 150W - Key components: - Electrolytic capacitors 470µF - 50V Code A0074 Available Price €13.49
Boost Adjustable Power Converter LM2587 5A DC 4.5-35V A high-performance step-up regulator Boost Adjustable Power Converter LM2587 5A DC 4.5-35V features: - Input voltage: 3.5 ~ 32v - Output voltage: 4.5 ~ 35v (adjustable) - Output current: 3A, maximum 5A (heatsink heat is required) - Conversion efficiency: up to 90% - Operating frequency: 100KHz - Short circuit protection: current limiting - Operating temperature: industrial grade (- 40 to 85) - PCB dimensions: 52 x 37 mm Code A0019 Available Price €6.99
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €5.95