Micro USB Interface Power Supply DC 7-12 VDC

Overhead power supply module with fixed 12 VDC output accepting a maximum current of 2A.
Works with frequency signals up to 1.2 MHz.
Characteristic:
- Input voltage range: 2 - 12 VDC,
- Fixed output voltage: 12 VDC,
- Output accuracy: ± 0.1 V,
- Maximum output current: 2A,
- Ripple at full load: Vpp & lt; 70mV,
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 17x13mm.

AC-DC to DC converter from 230V to 5V equipped with a housing.

DC to DC Step-up converter 1.5-4.2V to 5V. Operates with a maximum output current of 500mA.

Step-up power supply module with fixed 9 VDC output accepting a maximum current of 400mA.
Controlling the logic level of the signal sent on the EN pin, a module can be turned on / off.
Works with frequency signals up to 1.5 MHz.
Characteristic:
- Input voltage range: 2.5 - 7 VDC,
- Fixed output voltage: 9 VDC,
- On / off mode pin EN: signal EN allowing this function to be performed,
- Output accuracy: ± 0.1 V,
- Output current: 150 - 400 mA,
- No-load current: 0.2 mA, - Ripple at full load: Vpp & lt; 70mV,
- DC-DC conversion quality: 89%
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 19x15 mm.

- The XL6009 module has a superior performance than the LM2577 module
- The regulator-booster of High performance
Characteristic:
- Based on the XL6009E1 regulator
- Input voltage: 3V-32V,
- Output voltage: 5-35V (adjustable),
- Output current: 2A maximum 3A (heat sink is required)
- Conversion efficiency: up to 94%
- Rectifier: not synchronous rectification
- Short circuit protection: current limitation, since recovery
- Operating temperature: industrial grade (-40 ° C - 85 ° C)
- Load regulation: ± 0.5%
- Voltage regulation: ± 0.5%
- Size: 50 x 22 x 15 mm

DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.
Use a multimeter to check the output voltage and adjust the potentiometer.

MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features:
- Booster module
- The output voltage may be greater than the input voltage
- Use a multimeter to check the output voltage and adjust the potentiometer
- Input voltage: 2-24V
- Output voltage: 5-28V
- Current output: 2A - Operating temperature: -40ºC to + 85ºC
- Conversion efficiency: up to 93%
- Size: 17.5 x 30 mm

A high-performance regulator-booster.
24V battery charger - DC / CV method.
Power supply of the laptop from a 12V car battery.
A high-performance dimmer-regulator.
Charger for Li-Ion, Li-Po batteries etc. - CC / CV method.
LED Constant current driver for LED diodes.
Characteristic:
- Input voltage: 6V -40V
- Output voltage: 1.25-35V (adjustable)
- Output current: 8A, (10A maximum)
- Output power: 300W maximum
- Efficiency of Conversion: up to 95%
- Wiring: Solderless terminal
- Operating frequency: 300kHz
- Ambient temperature exceeds 40 ° C, increase heat dissipation
- LED indicator two-color;
- Charge red
- Fully charged light green
- No charge green

600W Boost Converter Booster Module DC voltage 12V to 80V features:
- Input voltage: 10V-60V
- Output voltage: 12-80V (adjustable)
- Output current: 10A
- Input current: 15A maximum
- Output power: 600W maximum
- Conversion efficiency: up to 95% (input 30V, output 40V 5A 93%)
- Wiring: solderless terminal
- The minimum difference between the output and input voltage: 2V
- The ambient temperature exceeds 40 ° C, increase the dissipation of heat
- Short circuit protection: If between reverse polarity protection: None
- Size: 85 x 63 x 64 mm
- Weight 275g
Applications:

The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden.