65x Cable Jumper Male Lot of 65 Male-Male jumper cables. Characteristic: -No soldering required -You can easily modify or revise the circuits -Quantity: 65 cables of different lengths and colors -Cable lengths: 120mm, 150mm, 200mm, 240mm Code K0010 Available Regular price €2.88 -€0.60 Price €2.28
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.12
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €2.55
40x Male to male cables 10cm 40x Male to male cables 10cm features: - Length: 10cm - Quantity: 40 cables - Dupont male connectors on both ends - Compatible with 2.54mm female connectors - High quality and good working condition - Easy to install and use Code K0107 Available Price €1.64
40x Female-Female Cable 20cm 40x Female-Female Cable 20cm features: -Length: 20cm -Quantity: 40 wires -Dupont female connectors on both ends -Compatible with 2.54mm male connectors -High quality and good working condition -Easy to install and use Code K0004 Available Price €2.06
25x M4x15 Nylon Round Separator Polyamide Insulators PCB M4 made of nylon for screws and fixings on PCB boards, model airplanes, DIY projects. It can be used in prototyping and robotics projects. 25x M4x15 Nylon Round Separator Polyamide Insulators PCB features: - Material PA66 - Type: female / female - Inner diameter M4 - Length body: 15mm - Quantity: 25 units - Color: white Code H0090 Available Price €0.16
Resistor 20K Ohm 5% 0,25W 1/4W Resistor 20K Ohm 5% 0,25W 1/4W features:-20 Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0022 Available Price €0.07
Support for HC-SR04 Ultrasonic Sensor Support for ultrasounds, HC-SR04 distance meter. Ideal to install the sensor on mobile platforms such as robots, vehicles, etc. Support for HC-SR04 Ultrasonic Sensor features: - Material: Acrylic - Color: transparent - Includes screws Code S0005 Available Regular price €1.20 -€0.50 Price €0.70
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.61
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.30
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.30
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.64
10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V This power supply delivers an output voltage lower than that of the input and allows power loads up to 10A. It has its heat sink, it is Recommended to use it for loads up to 8A for optimal cooling. Includes its foot protection kit, which greatly facilitates heat dissipation and use. 10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V features: - Input voltage: DC 8V-40V - Output voltage: DC 1.25V-36V adjustable with potentiometer (can only be used as a reducing module, the input must be higher than 1.25V output) - Output current: 8A (Max 10A for a short time), adjustable with potentiometer. Below 5A it can cool naturally - Output power: Max 150W - Key components: - Electrolytic capacitors 470µF - 50V Code A0074 ✗ Out-of-Stock Price €11.15
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.23
Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.06
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €7.84
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €2.88
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.23
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.61
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.30
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Available Price €3.30
Adjustable DC Module LM2596 1,25-32V 3A Step Down 3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features: - Based on the LM2596S-ADJ regulator - Rectification: Asynchronous - Output Voltage: 1.25v - 32v DC (adjustable) - Voltage of Input: 3.2v - 35v DC - Max Output Current: 3A (with heat sink) - Ripple at output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2.5% - Operating Temperature: -40ºC to + 85ºC - Measurements 43x 21x 14 mm Code A0004 Available Price €1.64
10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V This power supply delivers an output voltage lower than that of the input and allows power loads up to 10A. It has its heat sink, it is Recommended to use it for loads up to 8A for optimal cooling. Includes its foot protection kit, which greatly facilitates heat dissipation and use. 10A DC-DC Converter Adjustable Downstream 8V-40V to 1.25V-36V features: - Input voltage: DC 8V-40V - Output voltage: DC 1.25V-36V adjustable with potentiometer (can only be used as a reducing module, the input must be higher than 1.25V output) - Output current: 8A (Max 10A for a short time), adjustable with potentiometer. Below 5A it can cool naturally - Output power: Max 150W - Key components: - Electrolytic capacitors 470µF - 50V Code A0074 ✗ Out-of-Stock Price €11.15
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.23
Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.06
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €7.84
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €2.88
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.23