Wio Terminal - ATSAMD51 - RTL8720DN WiFi Bluetooth - Seeedstudio Wio Terminal: ATSAMD51 Core development board with Realtek RTL8720DN BLE 5.0 & Wi-Fi 2.4G / 5G. Arduino and MicroPython compatible, Wio Terminal is an ATSAMD51-based microcontroller with wireless connectivity compatible with Realtek RTL8720DN. Its CPU speed runs at 120MHz (Boost up to 200MHz). The Realtek RTL8720DN chip supports Bluetooth and Wi-Fi, providing the backbone for IoT projects. The Wio terminal itself is equipped with a 2.4 ”LCD screen, integrated IMU (LIS3DHTR), microphone, buzzer, microSD card slot, light sensor and infrared emitter (IR 940 nm). Code SS010 Backorder Price €55.49
Resistor 100K Ohm 5% 0,25W 1/4W Resistor 100K Ohm 5% 0,25W 1/4W features: 100K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0026 Available Price €0.08
Vertical Liquid Level Sensor Switch Level sensor for liquids with float. The liquid level sensor acts as a switch. The state is changed by means of a magnet located on the float. It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where it is necessary to control the level of non-corrosive liquids such as water tanks, aquariums. Characteristic: - Maximum Load: 50W - Maximum Switching Voltage: 250V - Maximum Switching Current: 0.5A - Maximum charging current: 1A - Operating temperature: -10ºC to + 60ºC - Size: 58mm x 18mm Code S0043 Available Price €2.95
Mosfet 24V 5A IRF520 PWM controller Mosfet 24V 5A IRF520 PWM controller features: - The IRF520 controller module can control the PWM signal from the Arduino module and adjust the DC voltage of So that we can control the speed of the DC motor, the brightness of the bulb, the LEDs, the heater. - The built-in IRF520 N-MOSFET transistor - Operating voltage: 3.3V -5V ( compatible with ARDUINO Raspberry PI) - Charging voltage: 0-24V - Charging current: up to 5A (more than 1A, the system must be equipped with a heat sink point) - 60W max power (more than 10W must be equipped with a heat sink) - Terminalblock connectors - LED indicating the presence of power - Dimensions: 33x24mm Code A0022 Available Price €2.49
1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino 1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL001 Available Price €2.39
Batch of 600 Units 1/4W Resistors Various values Ohm Ω Batch of 600 Units 1/4W Resistors Various values Ohm Ω features: - Each lot contains (30 x 20 units): 10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M - Tolerance: ± 5% - Power: 0.25W Code D0070 Available Price €3.95
NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA - This module includes PA preamplifier and LNA (Low-noise amplifier)- Comes with the SMA antenna for 2.4GHz (2dB)- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features: * Based on chip NRF24L01 +* Free band: 2.4GHz ISM* Speed: 250kbps, 1Mbps, 2Mbps* Work current- Reception: 45 mA- Transmission: 115 mA (4.2uA -sleep mode)* Receiving sensitivity:-104dB 250kbps- 95dB 1Mbps- 92dB 2Mbps* SPI interface Code W0063 Last items in stock Price €6.95
Potentiometer B10K linear Characteristic: -10k OHM kΩ - linear potentiometer 10k Arduino -Tolerance: +/- 20% - Power: 0.125W Code K0067 Available Price €0.99
3A DC Converter 4-53V Adjustable LM2596H Step Down Source Wide range of voltages, improved version. Drop module. They will use a multimeter to Check the output voltage and adjust the potentiometer. 3A DC Converter 4-53V Adjustable LM2596H Step Down Source features: - Based on the LM2596HVS-ADJ regulator - Rectification: Asynchronous - Output Voltage: 3v ~ 40v DC (adjustable) - Input Voltage: 4.5v - 53v DC - Max Output Current: 3A (with heat sink) - Ripple in output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5% - Operating temperature: -40ºC to + 85ºC - Measurements: 43x 21x 14 mm Code A0018 Available Price €2.79
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.95
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Last items in stock Price €3.99
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.49
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €9.49
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €3.38
XL4015 DC-DC 5A Digital Step-down LED Converter with Voltmeter, Ammeter and USB Output This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port. The output voltage and voltage can be adjusted thanks to two potentiometers present in the module. It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V - Output voltage: 1.25-32 V continuously adjustable - Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer, - Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power) - Operating temperature: -40 ° C - + 150 ° C Code A0077 Available Regular price €7.89 -€1.00 Price €6.89
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.99
Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.49
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.49
3A DC Converter 4-53V Adjustable LM2596H Step Down Source Wide range of voltages, improved version. Drop module. They will use a multimeter to Check the output voltage and adjust the potentiometer. 3A DC Converter 4-53V Adjustable LM2596H Step Down Source features: - Based on the LM2596HVS-ADJ regulator - Rectification: Asynchronous - Output Voltage: 3v ~ 40v DC (adjustable) - Input Voltage: 4.5v - 53v DC - Max Output Current: 3A (with heat sink) - Ripple in output voltage: 30mV - Frequency: 150KHz - Max Conversion Efficiency: 92% - Load Regulation: ± 0.5% - Voltage Regulation: ± 2,5% - Operating temperature: -40ºC to + 85ºC - Measurements: 43x 21x 14 mm Code A0018 Available Price €2.79
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.95
LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of tension.LM2596 DC Voltmeter Converter 3A Step Down Adjustable Power features:- Input voltage: 4.5-38V- Output voltage: 1.25-36.5V- Current output: 2A (max 3A with heat sink)- Operating temperature: -40 to + 85 ºC- Operating frequency: 150KHz- Efficiency conversion: up to 92%- Load Regulation: +/- 0.5%- Voltage Regulation: +/- 2.5%- Protection over temperature: the output switches off automatically- Size: 62mm x 38mm x 15mmPrincipal functions:- Step-down converter with overcurrent protection- Voltmeter up to 40V, remember to set the input voltage to 4.5V Code A0013 Last items in stock Price €3.99
Converter module AMS1117 Buck fixed output 5V 800mA This module is a voltage regulator that creates an output voltage of 5V with a maximum current of 800mA. The integrated regulator is referenced AMS1117. The module has two two point connectors for quick connection. Converter module AMS1117 Buck fixed output 5V 800mA features: - Based on the regulator AMS1117-5V - Input voltage: 4.5-12VDC - Output voltage: 5VDC (+/- 0.05V) - Max output current: 800mA - Operating temperature: -40C to + 150C - PCB size: 25x12 mm Code A0073 Available Price €1.49
Boost Buck Step Up-Down Automatic Converter Descripción:This is a powerful, efficient step-up (boost) and step-down (buck) switching voltage converter. It will automatically change between boosting and bucking to maintain a stable output voltage, regardless of the input.The output is set with a multi-turn potentiometer.Boost Buck Step Up-Down Automatic Converter features:- IC Chip: LM2577S-ADJ and LM2596S-ADJ - Module Properties: non-isolated Boost Buck constant current, constant voltage module (CC CV) charging module- Scope: High-power constant current LED driver.- Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Code A0017 Available Price €9.49
DC Step Down Converter 3.3V 2A 3.4-6V DC Step Down Converter 3.3V 2A 3.4-6V features: - Voltage drop module- Input voltage: 3.4-6V- Output voltage: 3.3V- Current output: adjustable, max 2A- Operating temperature: -40 to + 85 ºC- Operating frequency: 1.5MHz- Efficiency conversion: up to 95%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 12 x 15 mm- Full charge output ripple: Vpp <50 mV- Output accuracy: ± 0.1V- Current IQ without load: 0.2mA- Stop current (EN) <10uA Code A0068 Available Price €3.38
XL4015 DC-DC 5A Digital Step-down LED Converter with Voltmeter, Ammeter and USB Output This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port. The output voltage and voltage can be adjusted thanks to two potentiometers present in the module. It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V - Output voltage: 1.25-32 V continuously adjustable - Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer, - Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power) - Operating temperature: -40 ° C - + 150 ° C Code A0077 Available Regular price €7.89 -€1.00 Price €6.89
Converter DC USB Step Down 7V-24V to 5V 3A Converter DC USB Step Down 7V-24V to 5V 3A features:- Voltage reduction module with USB connector- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad- The USB output converter module has short circuit protection 5A current automatic protection- Based on the monolithic MP2307 controller- Rectification: not synchronous- Input voltage: DC 7v to 24v- Output voltage: DC 5v- Output current: 3A (Little time 4A)- Output connection: USB Type A female connector- Input connection: Terminal with screws- Efficiency of transformation: 96%- Switching frequency: 340KHz- Output ripple: 30mV (max.)- Load regulation: ± 0.5% Code A0016 Available Price €3.99
Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V Mini DC Converter 1.8A Downstream Voltage Regulator 4.7-23V to 1.0-17V features: - Voltage Drop Module - Use a multimeter to check the output voltage and adjust the potentiometer - Small size: 17mm x 11mm - Input voltage: 4.75-23V - Output voltage: 1.0-17V - Current output: 1.8A (peak max. 3A) - Operating temperature: -40 to + 85 ºC - Operating frequency: 240kHz - Conversion efficiency: up to 96% - Output ripple: 30mV (no-load) - Voltage regulation: ± 2.5% Code A0024 Available Price €2.49
AMS1117 Buck fixed output module 3.3V 800mA AMS1117 Buck fixed output module 3.3V 800mA features: - Based on AMS1117-3.3V regulator - Input Voltage: 4.5 - 12Vdc - Output Voltage: 3.3 Vdc (+/- 0,05V) - Max.output current: 800mA - Operating temperature: -40ºC to + 150ºC - Dimensions: 25mm x 12mm Code A0023 Available Price €1.49