AG BORAX 500g Unblocker

Flux rosin, solid resin, neutral pH for correct electronic soldering
- They do not cause corrosion of non-ferrous metals
- Does not cause short circuits
Melts with temperature, spreads over the area to be welded and penetrates into the most difficult corners cleans and prepares the surfaces and components to be welded, and facilitates adhesion and tin fluidity, improving soldering in electronics jobs.
Use a toothpick for the application. Do not apply excessively.
Safety:
- Use in ventilated spaces. Do not inhale the fumes that are given off by welding.
- Keep the bottle tightly closed and out of the reach of children.
- Do not ingest. Non-toxic
- Rarely irritating to skin contact

The product is a liquid, two component encapsulation mixture.
The curing takes place at room temperature.
The material provides thermal conductivity and low expansion.
Ideal for encapsulating or filling gaps in electronic heat generating components with metal enclosures or heat sinks.
It has an excellent fluidity when dosing and encapsulating.
After curing, it does not detach due to cyclic heating of the surface to which it adheres.
The cured product is dry to the touch.
Two-component silicone encapsulating compound 029 features:
- Manufacturer: TermoPasty,
- Mixing ratio: 100: 10,
- Thermal conductivity: 2 W / mK,
- Density: 1.15g / cm3,
- Pre-crosslinking: 30-40 min,
- Working temperature from -50ºC to + 200ºC,

The PCB PLUS cleaner is designed for printed circuit boards.
Dissolves waste flux, including resin.
The liquid does not attack the substrate or the structural components of the printed circuit boards.
The special brush to remove particles and smaller debris. Perfect for cleaning PCB after repair and assembly.
PCB Plus Cleanser Spray 400ml features:
- Form: spray
- Capacity: 400ml
Application:
- The product does not leave deposits
- It evaporates very fast
- Eliminates waste after welding
- Perfect in any electronic service
- The product does not react with most plastics used in electronics

Graphite Grease Spray Anticorrosive 100ml features:
Graphite Grease- the product has excellent lubricating qualities and is provides an effective anticorrosive protection. The addition of graphite increases its resistance to burdens and the action of cold water. Application: - Car leaf springs
- Worm gear
- Change gear train
- Screw thread
- Screwbolt which are exposed to corrosion
- Chains and other hardly burden nodes of friction working in a temperature range from -20°C to 50°C

Totally new and of high quality.
Dissipate the heat of the computer by refrigerating it effectively.
It is used to attach passive dissipaters to graphic memories and chip plates and LED diodes.
Make sure to put the components correctly, once it has dried it will not be able to detach. Adhesive Thermal Paste Glue 10g CPU features:
  - Color white
- Surface drying time [25 ° C, min]: 2- 8
- Hardness: 45 -75
- Tensile strenght (Mpa): 2.0
- Elongation (%): 100
- Thermal Conductivity W / mk:> 1,0
- Volume Resistance (c-in / W): <2.0 x 10 * 15
- Dielectric strength (KV / mm): 20
- Dielectric Constant: 3.0
- Dielectric loss factor (60Hz): 0.003
- Operating temperature (max): 200 ° C

Liquid for cleaning LED boards.
The fluid quickly and effectively cleans even the most persistent dirt on the surface of the boards.
Eliminates traces of marker, scratches and discoloration resulting from long term use of the board.
Cleaning liquid for LED boards 250ml features:
- Manufacturer: AG Chemia,
Content:
- A 250ml aerosol.

Thermo Silicone Paste Cleaner features:
This product is safe and easy to use with a pleasant aroma of citrus.
It is used to eliminate old conductive pastes from heat, worn out. How to use: - It is recommended to remove the most amount of paste consumed a small amount of liquid applied to the fabric applied to the surface that is cleaned
- Wait 1-2 minutes
- Clean with a cloth

Label Killer Spray 300ml features:
Removes labels form all kinds of packaging. Caution: the preparation may imperceptibly dissolve a colorful print under the removed label as well as dissolve some plastics - caution recommended!
Directions for use: The preparation has to be spread directly over a label for some 3 minutes. Use cloth or tissue to wipe remaining glue
- Office and IT equipment
- Cash registers
- Labelling and packaging machines
- Household appliances