AG Extreme thermal grease 3g syringe

Ideal to control the speed of DC motors.
Characteristic:
- Input voltage: 10-30VDC,
- Max continuous output current: 5A (peak current 10A),
- Max power: 120W,
- Dimensions: 61x27.9x45.7mm,
- PWM frequency: 16kHz,
- Adjustable duty cycle: 5% -100%,
- Integrates a regulator L7805CV TO- 220,
- Incorporates a 10A fuse to protect the power circuit.
Please note that the voltage applied to the motor will be the supply voltage applied to the circuit.

The four-way wireless smart receiving controller features four relays, which can control on / off as a switch for various special control applications. The product has the characteristics of stable performance, small size and high reception sensitivity. It is mainly used in electric doors, windows, lifting equipment, security and control systems etc. The controller supports a variety of different wireless remote controllers, such as 2262/2260/1527/2240.

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip
- Voltage: 3.2-3.4V 
- Current: 350mA 
- Luminous flux: 100-110LM 
- Ã beam angle: 140 degrees 
- Color emission: pink

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip
- Voltage: 3.0-3.2V
- Current: 300mA
- Luminous flux: 70-80LM
- Ã beam angle: 120 degrees
- Color emission: green

SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features:
Flux liquid alcohol-based for electronic welding.
Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive
Form: liquid
Capacity: 50ml
Content of solid bodies: 0 ... 5%
Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.
It cleans easily with alcohol.
It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.
- Keep the boat tightly closed and far away from the children.
- Use in ventilated spaces.

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip
- Voltage: 2.2-2.4V
- Current: 300mA
- Luminous flux: 40-50LM
- Ã beam angle: 120 degrees
- Color emission: red

Converter DC USB Step Down 7V-24V to 5V 3A features:
- Voltage reduction module with USB connector
- DIY mobile power supply, to achieve the 5v output to charge the phone, mp3, mp4, psp, etc. can not charge for the ipad
- The USB output converter module has short circuit protection 5A current automatic protection
- Based on the monolithic MP2307 controller
- Rectification: not synchronous
- Input voltage: DC 7v to 24v
- Output voltage: DC 5v
- Output current: 3A (Little time 4A)
- Output connection: USB Type A female connector
- Input connection: Terminal with screws
- Efficiency of transformation: 96%
- Switching frequency: 340KHz
- Output ripple: 30mV (max.)
- Load regulation: ± 0.5%

Isopropyl alcohol is used for cleaning: - Of electronic devices, such as contact tips (such as those of ROM cartridges).
- magnetic tapes and disc heads (such as those of audio and video recorders and flexible disk drives).
- laser lenses in optical disk drives (for example: CD, DVD) and the removal of thermal paste from heat sinks and integrated circuit packages (for example: CPU) of the keyboard and the LCD screen. Very used in the cleaning of lenses of photographic lenses and contacts of electronic devices, since it does not leave marks and is of rapid evaporation. It is sold commercially also as a cleaner for shales.