Protoboard Breadboard 9x15cm Protoboard Breadboard 9x15cm features: -PCB dimension: 9x15cm-Hole diameter: 1mm -Pitch: 2.54mm-Bakelite with copper fields Code PB016 Available Price €0.75
Flux Gel Jeringa 1.4cm3 RMA Soldering BGA SMD SMT Flux gel syringe 1.4cm3 of RMA class, intended for SMT assembly and repairs. Flux gel can be applied through a sieve, pattern or from a syringe. Activators utilized in flux manufacturing process enable to leave its remnants after soldering on the package (as far as the process does not include washing phases). Code Q0018 Available Price €2.49
2WD Round Car Chassis 2x Ultrasonic Sensor Contents: - 2x Round transparent chassis plate diameter of 14cm - 2x DC 5V gear motor - 2x 6.5cm wheels (Dia .) x 2.6cm (H) - 2x Encoder discs - 2x Idlers - 2x HC-SR04 ultrasonic sensor, distance meter - 2x Holder for HC-SR04 - 1x Battery holder 2xAA (batteries not included) - Screws for assembly Motor characteristic: - Voltage: 3 at 6Vdc - Reducer: 1:48 - No load speed: 100 RPM at 6Vdc - No load current: 90mA at 3Vdc - 180mA at 6Vdc Code R0005 Available Price €22.45
Thermal Silicone Paste 7g Heat Sink It facilitates the transfer of heat between the electronic components and the radiator.It is necessary for the correct operation of any type of temperature sensors.It is characterized by a very good chemical resistance for oxidation, water solutions of acids, alkalis and salts, sulfur dioxide and ammonia. It has a very wide range of working temperatures. High quality - manufactured in EU Thermal Silicone Paste 7g Heat Sink features: - Density at 20 ° C: 2.58 G / cm3- Flash point: 350 ° C- Freezing point: -50 ° C- Refractive coefficient: 1.405- Specific heat at 50 ° C: 0.243 Cal / g K- Global coefficient of heat transfer at 0-150 ° C: 0.88 W / m K- Dielectric constant at 100 Hz: 4.7 (± 0.1) Code Q0051 Available Price €2.49
Resistor 150R Ohm 5% 0,25W 1/4W Resistor 150R Ohm 5% 0,25W 1/4W features:-150R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0006 Available Price €0.08
BME280 Digital Temperature Humidity Barometric Pressure Module This module includes the component BME280 that is translated into a digital signal.The equipment uses the two I2C and SPI interfaces. The BME280 does not allow the module to be used as an altimeter as opposed to its successor BMP280.Its 5-pin straight connector allows easy connection to other electronic boards. BME280 Digital Temperature Humidity Barometric Pressure Module features: - Interfaces:- I2C (up to 3.4 MHz)- SPI (up to 10 MHz)- Supply voltage: 1.8-5VDC- Module operating range:- Temperature: -40ºC to + 85ºC- Humidity: 0-100%- Pressure: 300-1100 hPa- Resolution of the measures:- Temperature: 0.01ºC- Humidity: 0.008%- Pressure: 0. 18Pa- Accuracy of the measures:- Temperature: +/> Code M0135 Available Price €14.95
2x Cable Alligator Clip Black and Red Multimeter 2x Cable Alligator Clip Black and Red Multimeter features: - Length: 90cm- Colors: red and black- Quantity: 2 Cables Code K0016 Available Price €2.99
Micro Motor 3V 5V 6V DC with cable conector male For Arduino, Smart Car, Robotics.Small electric motor magnet for direct current (DC). Micro Motor 3V 5V 6V DC with cable conector male features: - Operating voltage: 1.5V to 6V - Cable 16cm with male connector - DC current: 350mA - Torque max.: 15g / cm- Max speed: 12000rpm- Weight: 16.5 g Code R0080 Available Price €1.95
4N35 DIP Optocoupler 30V 60mA - 2pcs 4N35 DIP Optocoupler 30V 60mA - 2pcs features: -NPN Phototransistor Optocoupler Code T0019 Available Price €0.79
74HC00N DIP14 Input NAND Gate NXP Integrated Circuit 74HC00N DIP14 Input NAND Gate NXP Integrated Circuit features: - Blister: DIP14- Number of pins: 14- Step between pins: 2.54 mm- Manufacturer: NXP - Input voltage VCC: 2 - 6 VDC- High level input voltage V (IH): 1.2 - 3.2 VDC- Low level input voltage V (IL): 0.8 - 2.8 VDC- Input voltage V (I): 0 - 6 VDC- Output voltage V (O): 0 - 6 VDC- High level output voltage V (OH): 2 - 6 VDC- Low level output voltage V (OL): 0 - 0.16 VDC - Leakage current I (I): ± 1 μA- Supply current I (CC): 40 μA - Operating temperature: -40 ° C to 125 °C- Storage temperature: -40 ° C to 125 °C Code T0050 Available Price €1.10
74LS86N DIP14 Input Logic NAND Gates O-Exclusive 74LS86N DIP14 Input Logic NAND Gates O-Exclusive features: - Blister: DIP14- Number of pins: 14- Step between pins: 2.54 mm- Manufacturer: Texas Instrument - Input voltage VCC: 4.75 - 5.25 VDC- High level input voltage V (IH): 2 VDC- Low level input voltage V (IL): 0.8 VDC- Input clamp voltage V (IK): -1.5 VDC- High level output voltage V (OH): 2.4 - 3.4 VDC- Low level output voltage V (OL): 0.2 - 0.4 VDC - High level output current I (OH): -800 μA- Low level output current I (OL): 16 mA- Input current to VCC: 1 mA- High level input current I (IH): 40 μA- Low level input current I (IL): -1.6 mA- Short circuit output current I (OS): -55 - -18 mA Code T0048 Available Price €1.10
SN74LS47N BCD 7-Segment Decoder/Driver Integrated Circuit SN74LS47N BCD 7-Segment Decoder/Driver Integrated Circuit features: - Blister: DIP16- Number of pins: 16- Step between pins: 2.54 mm- Manufacturer: from China - Input voltage VDD: 4.75 - 5.25 VDC- High level input voltage V (IH): 2 VDC- Low level input voltage V (IL): 0.8 VDC- Voltage of the input clamp diode V (IK): -1.5 - -0.65 VDC- High level output voltage V (OH): 2.4 - 4.2 VDC- Low voltage output voltage V (OL): 0.35 - 0.5 VDC- Input voltage in V state (I on): 0.35 - 0.5 VDC- Output voltage out of state V (I off): 15 VDC - High level input current I (IH): 20 μA - 0.1 mA- Low level input current I (IL): -1.2 - -0.4 mA- High level output current I (OH): - 50 μA Code T0059 Available Price €1.10
2x CD4056BE 7 Segment BCD Decoder Integrated CD 4056 DIP 2x CD4056BE 7 Segment BCD Decoder Integrated CD 4056 DIP features: - Product: LCD CMOS controllers- Number of segments: segment 4: 7- Maximum clock frequency: 8 MHz- Operating supply voltage: 3V to 18V- Minimum operating temperature: - 55 C- Maximum operating temperature: + 125 C- Package / box: PDIP-16 - Mounting style: Through Hole- Operating temperature range: - 55 C to + 125 C- Pd - Dissipation power: 500 mW- Supply current - Max: 300 uA- Quantity: 2 units Code T0021 Available Price €1.04
HT9170D SOP18 Holtek Multi-Frequency Dual Tone Receiver HT9170D SOP18 Holtek Multi-Frequency Dual Tone Receiver features: - Blister: SOP18- Number of pins: 18- Step between pins: 1.27 mm- Manufacturer: Holtek - Operating voltage VDD: 2.5 - 5.5 VDC- High input voltage level V (IH): 4.0 VDC- Input voltage low level V (IL): 1.0 VDC - I (DD) operating current: 3 - 7 mA- Standby current I (STB): 10 - 25 μA- High input current level I (IH): 0.1 μA- Input current low level I (IL): 0.1 μA- Current source (D0-D3, EST, DV) I (OH): -0.8 - -0.4 mA- Drop current (D0-D3, EST, DV) I (OL): 1.0 - 2.5 mA- Frequency system f (osc): 3.5759 - 3.5831 MHz - Operating temperature: -20 ° C to 75 ° C - Storage temperature: -50 ° C to 125 ° C Code T0063 Available Price €1.10
74HC00N DIP14 Input Positive Logic NAND Gates 74HC00N DIP14 Input Positive Logic NAND Gates features: - Blister: DIP14- Number of pins: 14- Step between pins: 2.54 mm- Manufacturer: Texas Instrument - Input voltage VCC: 2 - 6 VDC- High level input voltage V (IH): 1.5 - 4.2 VDC- Low level input voltage V (IL): 0.5 - 1.8 VDC- Input voltage V (I): 0 - 6 VDC- Output voltage V (O): 0 - 6 VDC- High level output voltage V (OH): 1.9 - 5.9 VDC- Low level output voltage V (OL): 0.1 - 0.33 VDC - Leakage current I (I): ± 1000 nA- I (DC) supply current: 20 mA - Operating temperature: -40 ° C to 85 ° C- Storage temperature: -65 ° C to 150 ° C Code T0049 Available Price €1.10
2x PCF8574P I/O Extension Board 8574 NXP - The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt. - Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)). - Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V. - Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs. - System Master can read from the input port or write to the output port through a single register. Code T0010 Available Price €1.15
L293D Quadruple Motor Controller PaP Half-H Driver No STM L293D Quadruple Motor Controller PaP Half-H Driver No STM features: - Voltage: 7V to 36V- Output current: 600 mA- Operating temperature: 0C to + 70C- Manufacturer: China- Quantity: 1 unit We offer a very extensive list of electronics components.Most shipments are made within a maximum period of one day from the moment the payment is confirmed. Code T0045 Available Price €1.49
L293D Quadruple Half-H Drivers STM L293D Quadruple Half-H Drivers STM features:-Continue 0.6A half-h driver STM Arduino Code T0014 Last items in stock Price €1.85
4N35 DIP Optocoupler 30V 60mA - 2pcs 4N35 DIP Optocoupler 30V 60mA - 2pcs features: -NPN Phototransistor Optocoupler Code T0019 Available Price €0.79
74HC00N DIP14 Input NAND Gate NXP Integrated Circuit 74HC00N DIP14 Input NAND Gate NXP Integrated Circuit features: - Blister: DIP14- Number of pins: 14- Step between pins: 2.54 mm- Manufacturer: NXP - Input voltage VCC: 2 - 6 VDC- High level input voltage V (IH): 1.2 - 3.2 VDC- Low level input voltage V (IL): 0.8 - 2.8 VDC- Input voltage V (I): 0 - 6 VDC- Output voltage V (O): 0 - 6 VDC- High level output voltage V (OH): 2 - 6 VDC- Low level output voltage V (OL): 0 - 0.16 VDC - Leakage current I (I): ± 1 μA- Supply current I (CC): 40 μA - Operating temperature: -40 ° C to 125 °C- Storage temperature: -40 ° C to 125 °C Code T0050 Available Price €1.10
74LS86N DIP14 Input Logic NAND Gates O-Exclusive 74LS86N DIP14 Input Logic NAND Gates O-Exclusive features: - Blister: DIP14- Number of pins: 14- Step between pins: 2.54 mm- Manufacturer: Texas Instrument - Input voltage VCC: 4.75 - 5.25 VDC- High level input voltage V (IH): 2 VDC- Low level input voltage V (IL): 0.8 VDC- Input clamp voltage V (IK): -1.5 VDC- High level output voltage V (OH): 2.4 - 3.4 VDC- Low level output voltage V (OL): 0.2 - 0.4 VDC - High level output current I (OH): -800 μA- Low level output current I (OL): 16 mA- Input current to VCC: 1 mA- High level input current I (IH): 40 μA- Low level input current I (IL): -1.6 mA- Short circuit output current I (OS): -55 - -18 mA Code T0048 Available Price €1.10
SN74LS47N BCD 7-Segment Decoder/Driver Integrated Circuit SN74LS47N BCD 7-Segment Decoder/Driver Integrated Circuit features: - Blister: DIP16- Number of pins: 16- Step between pins: 2.54 mm- Manufacturer: from China - Input voltage VDD: 4.75 - 5.25 VDC- High level input voltage V (IH): 2 VDC- Low level input voltage V (IL): 0.8 VDC- Voltage of the input clamp diode V (IK): -1.5 - -0.65 VDC- High level output voltage V (OH): 2.4 - 4.2 VDC- Low voltage output voltage V (OL): 0.35 - 0.5 VDC- Input voltage in V state (I on): 0.35 - 0.5 VDC- Output voltage out of state V (I off): 15 VDC - High level input current I (IH): 20 μA - 0.1 mA- Low level input current I (IL): -1.2 - -0.4 mA- High level output current I (OH): - 50 μA Code T0059 Available Price €1.10
2x CD4056BE 7 Segment BCD Decoder Integrated CD 4056 DIP 2x CD4056BE 7 Segment BCD Decoder Integrated CD 4056 DIP features: - Product: LCD CMOS controllers- Number of segments: segment 4: 7- Maximum clock frequency: 8 MHz- Operating supply voltage: 3V to 18V- Minimum operating temperature: - 55 C- Maximum operating temperature: + 125 C- Package / box: PDIP-16 - Mounting style: Through Hole- Operating temperature range: - 55 C to + 125 C- Pd - Dissipation power: 500 mW- Supply current - Max: 300 uA- Quantity: 2 units Code T0021 Available Price €1.04
HT9170D SOP18 Holtek Multi-Frequency Dual Tone Receiver HT9170D SOP18 Holtek Multi-Frequency Dual Tone Receiver features: - Blister: SOP18- Number of pins: 18- Step between pins: 1.27 mm- Manufacturer: Holtek - Operating voltage VDD: 2.5 - 5.5 VDC- High input voltage level V (IH): 4.0 VDC- Input voltage low level V (IL): 1.0 VDC - I (DD) operating current: 3 - 7 mA- Standby current I (STB): 10 - 25 μA- High input current level I (IH): 0.1 μA- Input current low level I (IL): 0.1 μA- Current source (D0-D3, EST, DV) I (OH): -0.8 - -0.4 mA- Drop current (D0-D3, EST, DV) I (OL): 1.0 - 2.5 mA- Frequency system f (osc): 3.5759 - 3.5831 MHz - Operating temperature: -20 ° C to 75 ° C - Storage temperature: -50 ° C to 125 ° C Code T0063 Available Price €1.10
74HC00N DIP14 Input Positive Logic NAND Gates 74HC00N DIP14 Input Positive Logic NAND Gates features: - Blister: DIP14- Number of pins: 14- Step between pins: 2.54 mm- Manufacturer: Texas Instrument - Input voltage VCC: 2 - 6 VDC- High level input voltage V (IH): 1.5 - 4.2 VDC- Low level input voltage V (IL): 0.5 - 1.8 VDC- Input voltage V (I): 0 - 6 VDC- Output voltage V (O): 0 - 6 VDC- High level output voltage V (OH): 1.9 - 5.9 VDC- Low level output voltage V (OL): 0.1 - 0.33 VDC - Leakage current I (I): ± 1000 nA- I (DC) supply current: 20 mA - Operating temperature: -40 ° C to 85 ° C- Storage temperature: -65 ° C to 150 ° C Code T0049 Available Price €1.10
2x PCF8574P I/O Extension Board 8574 NXP - The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt. - Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)). - Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V. - Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs. - System Master can read from the input port or write to the output port through a single register. Code T0010 Available Price €1.15
L293D Quadruple Motor Controller PaP Half-H Driver No STM L293D Quadruple Motor Controller PaP Half-H Driver No STM features: - Voltage: 7V to 36V- Output current: 600 mA- Operating temperature: 0C to + 70C- Manufacturer: China- Quantity: 1 unit We offer a very extensive list of electronics components.Most shipments are made within a maximum period of one day from the moment the payment is confirmed. Code T0045 Available Price €1.49
L293D Quadruple Half-H Drivers STM L293D Quadruple Half-H Drivers STM features:-Continue 0.6A half-h driver STM Arduino Code T0014 Last items in stock Price €1.85