20x Ceramic Capacitor 470pF 50v 2,54 PCB PIC for Arduino

10x Electrolytic Capacitor 100 uF 50V 105ºC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 100uF
-Maximum tension: 50V
-Maximum temperature: 105º C
-Dimensions: 6x11mm
-Quantity: 10 units

1N4007 Rectifier Diodes 1A 1000V DO-41 features:
- Standard rectifier diode
- Configuration: Simple
- Reverse voltage: 1000V
- Direct voltage drop: 1V
- Direct direct current: 1A
- Maximum overvoltage current: 30A
- Encapsulated: DO-41
- Operational tension: -65ºC to + 125ºC

Batch of 600 Units 1/4W Resistors Various values Ohm Ω features:
- Each lot contains
(30 x 20 units):
10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M
- Tolerance: ± 5%
- Power: 0.25W

LED 10-Segment Bar Graphics Display Red features:
- Bargraph LED display
- Number of segments: 10
- Size: 5mm - Dimensions: 25x10mm
- Material GaAsP / GaP
- Color: red
- Wavelength: 635 nm
- Vf / forward /2.1 V
- I fw / forward / 30 mA
- Iv / Ifw = 20mA / 4 mcd
- Number of terminals: 20

20x Ceramic Capacitor 100pF 50v 2,54 PCB PIC Arduino 0.022uF features:
-Type: ceramic NPO
-Tolerance: +/-5%
-Dimensions: diameter 5mm, pitch 2.54mm

15x Electrolytic Capacitor 1uF 50V 105º C PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 1uF
-Maximum tension: 50V
-Maximum temperature: 105º C
-Dimensions: 5x11mm
-Quantity: 15 units

Bridge Rectifier KBL10 - 4A/1000V features:
- Maximum reverse voltage: 1000 V
- Vf - Front tension: 1.0 V
- Max. Overvoltage current: 200 A
- Minimum operating temperature: - 50 C
- Maximum operating temperature: + 150 C
- Go - Reverse current: 10 uA
- Quantity: 1 unit

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip
- Voltage: 3.0-3.2V
- Current: 300mA
- Luminous flux: 70-80LM
- Ã beam angle: 120 degrees
- Color emission: green