TP4056 Lithium Battery Charger Module 5V Micro USB

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

RTC DS3231 clock module with EEPROM 32k.
High precision RTC module.
Can be used in projects of Arduino, PIC, AVR, STM32 and other.
DSC321 AT24C32 with Real Time Clock RTC Battery features:
- Based on DS3231
- EEPROM AT24C32 (32K)
- I2C interface
- LED work indicator
- Includes CR2032 3V battery

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

Cable 1x0.35 Flexible single-pole 0.35mm² black features:
-Conductor: Flexible Copper
-Insulation: PVC
-Low voltage electrical cables
-Standard: EN 50525-2-31
-Number of conductors: 1x0.35mm²
-Service voltage: 300 / 500V
-Service temperature: at 70ºC
-Resistance at 20ºC: 55.0 Ohm / Km
-Weight (Kg / Km): 7
-Outer Diameter: 2.4mm

Power supply module step up with fixed output 5 VDC accepting a maximum current of 2A.
Works with frequency signals up to 1.2 MHz.
Characteristic:
- Input voltage range: 2 - 5 VDC,
- Fixed output voltage: 5 VDC,
- Output accuracy: ± 0.1 V,
- Maximum output current: 2A,
- Ripple at full load: Vpp & lt; 70mV,
- Operating temperatures: -40ºC - + 85ºC,
- PCB size: 17x13mm.

TP4056 Module Lithium Battery Charger with Protection features:
- TP4056 Li-Ion Micro USB Charger
- Upgraded version of previous TP4056
- Micro USB connection to charge directly from the PC
- Ideal for 18650 batteries
- Based on the TC4056A regulator
- Input Voltage: 4.5V - 5.5V DC
- Full charge voltage: 4.2V +/- 1.5%
- Max Output Current: 1A
- Overvoltage protection 4.2V
- Over discharge protection 2.4V
- LED indicator: charging blue, charging red
- Operating temperature: -10ºC to + 85ºC
- IN + and IN- connection for electronic circuits
- Overcurrent protection: 3A
- Measurements 26 x 19 x 5 mm
- Possibility of current change through Rprog

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.
Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features:
- Type: 3-axis accelerometer
- Chip: ADXL345
- Supply voltage: 3-5V
- Consumption: 40uA active and 0.1uA on hold
- Communication: SPI and I2C
- Measurements: Static and dynamic acceleration
- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g
- Resolution: 13 bits
- Dimensions: 20x16mm
- Operating temperature: -40 °C to +80 °C
- Detection: Free fall, click-double click

Momentary Switch Push Button Red N/O 7mm features:
- Momentary pushbutton N/O (normally open)
- Red button
- Dimensions approx. 7 mm x 27 mm
- Recessed with nut and washer
- Load current (supported): 1A to 230V / 2A to 125V
- Drill to embed: 7 mm +/- 0.2
- Operating temperature: -55º to +85ºC