Tin Coil Sn60Pb40 Flux Wire 0.3mm 3g The ideal tin for application in consumer electronics circuits, especially mobile phones and tablets. 3g of 0.3mm diameter tin wire. Consists of 60% tin, 40% lead. Code Q0121 Available Price €1.49
IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features: - Based on the PCF8574A chip - Power: 5V - Supports I2C Protocol - A potentiometer for regulate contrast - Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20 PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL - Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32 Code P0008 Available Price €1.39
Battery Holder 6x AA with DC Connector 9V LR06 Ideal to power your Arduino board.Battery Holder 6x AA with DC Connector 9V LR06 features:- Cable 12cm long,- Measures 90x 55x 15mm,- Max 50mm pile length,- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7). Code PP008 Available Price €1.85
Female DC Power Connector Jack 2.1x5.5mm Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Female DC Power Connector Jack 2.1x5.5mm features: - Ideal for connecting without welding- It has two screws in the tip for positive and negative cable screwdriver Code K0050 Available Price €0.49
Servos Tester Servos Tester features: - 3-Channel Tester - For Electronica Arduino Code R0029 Available Regular price €2.79 -€1.00 Price €1.79
Double Side Prototype Board PCB 8x12cm Double Side Prototype Board PCB 8x12cm features: -Thickness of PCB: 1.6mm-Material: high quality FR-4 glass fiber PCB-Presented and numbered on both sides-Top and bottom are identical copper layers-Pads grid (pitch) 2.54mm/0.1", hole diameter 0.9mm Code PB018 Available Price €2.69
Cutting Pliers 130mm Cutting Pliers 130mm features: - This model is not isolated, please use it without current- Use to cut soft materials, electronic components, cables, plastic card- Can also be used for welding work Code H0051 Available Price €4.29
Rechargeable Battery XTAR 18650 2600mAh Li-ion Rechargeable Battery XTAR 18650 2600mAh Li-ion features: - With PCB protection circuit that protects the battery against overcharges and over-discharges, increasing battery life - Quantity: 1 unit Code PP028 ✗ Out-of-Stock Price €9.99
PowerBank 20000mAh 22.5W PD QC3.0 AFC Power Bank 20000 mAh hasta 22,5 W Joyroom, compatible con tecnologías de carga rápida (PD, QC 3.0, AFC) El Power Bank Joyroom JR-QP192 tiene 4 puertos integrados: 1 entrada micro USB, 2 salidas USB y 1 entrada/salida USB C. Code KH020 Available Regular price €25.90 -€2.00 Price €23.90
PowerBank 10000mAh 15W PD QC3.0 AFC Power Bank 10000 mAh hasta 15 W Joyroom, compatible con tecnologías de carga rápida (PD, QC 3.0, AFC) El Power Bank Joyroom JR-T013 tiene 4 puertos integrados: 1 entrada micro USB, 2 salidas USB y 1 entrada/salida USB C. Code KH050 Available Price €18.90
Solar Power Manager, Embedded 10000mAh Li-Po Battery Solar power manager (B), Built-in 10000mAh rechargeable Li-Po battery, Multiple protection circuits. Compatible with 6V~24V solar panels, Rechargeable from solar panel or C-type power adapter. 5V/3A regulated output. Code WV005 Available Price €35.95
Diagnostic meter, OBD2 scanner, battery tester Konnwei KW870 Konnwei's KW870 car battery tester is capable of effectively analysing and reading important car data such as voltage, internal resistance, cold start current and AH capacity. In addition, the device calculates cold-start capacity and the degree of ageing, allowing for faster and more accurate repairs. Whether you're a beginner or an expert, this car battery diagnostic device can be used with a wide range of 6-18 V batteries with a capacity of 100-2000 CCA, including traditional, flat AGM, spiral AGM and gel batteries. Code H0590 Last items in stock Price €89.95
Car battery tester and charger Konnwei KW510 The Konnwei KW510 is an advanced multi-function device that uses state-of-the-art technology to allow you to easily, quickly and accurately measure the actual cold start capability, battery condition and common faults in the vehicle's starting and charging systems. The KW510 is particularly useful for workshops as it can accurately detect the problem, allowing the vehicle to be repaired quickly. Code H0586 Available Price €69.95
Charger 4 x 9V 6F22 with EU Power Supply Cable Charger 4 x 9V 6F22 with EU Power Supply Cable features: The everActive NC 109 charger is a unique, specialized design that allows you to charge from 1 to 4 pieces of 9V Ni-MH batteries - each cell is charged individually.It allows you to charge up to 4pcs of 9V batteries simultaneously, in any configuration / combination, with any capacity, any manufacturer.The charger has 4 independent charging channels.The most important features: of the NC109 loader:- quick charging of a large number of batteries simultaneously - ideal for industrial and professional applications,- individual LED indicator of charger work for each cell - with full charge signaling,- 100-240V AC power adapter included, optionally a 12V car adapter is available, Code A0101 Available Price €17.99
Solar Power Manager Supports 3x 18650 Batteries Solar Power Manager (C), Supports 3x 18650 Batteries, Multi Protection Circuits. Compatible with 6V~24V solar panels, Rechargeable from solar panel or C-type power adapter. 5V/3A regulated output. Code WV006 Available Price €31.95
Wireless charger module 5V 2V with transmitter coil. Wireless charging and powering of small electronic products. It is designed for small size, ease of use, high performance and low price. The main purpose of the module is to be used in the initial phase of projects such as mobile electronic products. Code A0174 Available Price €8.95
Charger SkyRC iMax B6 V2 6A 60W SKYRC IMAX B6 V2 Original Balance Charger Charger for DJI Mavic TB4X / NiMH / NiCD / LiHV / NiCd / PB / Li-ion 6A 60W. The charger offers a built-in power of 60W and a charging current of up to 6A. It is also compatible with the DJI Mavic/Inspire battery with a maximum charging power of 4A. Code A0173 Available Price €45.90
3S BMS 25A 12.6V 18650 PCM PCB Circuit Charging Module. In the case of a battery pack, the BMS (Battery Management System) balancing protection circuit allows charging and discharging to be individually controlled. That is, the circuit controls that all cells are charged and discharged at approximately the same voltage. The current during charging should be limited, because the cell will "absorb" the current given to it, but a higher current than the one established by the manufacturer (generally a safe current is 1C ) can cause the cell to overheat and, in extreme cases, explode. The same relationship also applies to discharge. Code A0106 Available Price €4.49
Wireless charger module 5V 1V with transmitter coil. Wireless charging and powering of small electronic products. It is designed for small size, ease of use, high performance and low price. The main purpose of the module is to be used in the initial phase of projects such as mobile electronic products. Code A0175 Available Price €7.95
Type-C High Power Fast Charging Module DC 5V 9V 12V 20W Wireless charging and powering of small electronic products. It is designed for small size, ease of use, high performance and low price. Type-C High Power Fast Charging Module DC 5V 9V 12V 20W Wireless Charger Transmitter Circuit Coil Charger Board 0-8mm max 10mm Code A0176 Available Price €10.95
TP4056 Lithium Battery Charger Module 5V Micro USB TP4056 5V Micro USB Lithium Battery Charger Module features: - Based on TP4056ES regulator - Lipo micro USB Li-Ion charger - Input Voltage: 4.5V - 5.5 VDC - Full charge voltage: 4.2V +/- 1.5% - Max Output Current: 1A - Indicator LED: charging red, charging green - Operating temperature: -10ºC to + 85ºC - IN + and IN- connection for electronic circuits - Battery protection against over-discharge voltage: 2.5V - Protection against over current battery: 3A - Measurements: 25x19x5 mm - Ideal for 18650 batteries Code A0100 Available Price €0.99
Charger for 4 Ni-MH R6/AA,R03/AAA Rechargeable Batteries everActive NC-450 The European plug-in charger for charging 4 rechargeable batteries at the same time, each charge is individually displayed. Advanced processor controls the charging process with "delta V" function. Code A0133 Available Price €15.99
TP4056 Lithium Battery Charger Module 5V Mini USB TP4056 Lithium Battery Charger Module 5V mini USB features: - Based on TP4056ES regulator - Lipo mini USB Li-Ion charger - Input Voltage: 4.5V - 5.5 VDC - Full charge voltage: 4.2V +/- 1.5% - Max Output Current: 1A - Indicator LED: charging red, charging green - Operating temperature: -10ºC to + 85ºC - IN + and IN- connection for electronic circuits - Battery protection against over-discharge voltage: 2.5V - Protection against over current battery: 3A - Measurements: 25x19x5 mm - Ideal for 18650 batteries Code A0008 Available Price €0.99
Charger 2x18650 with EU Plug Cable Charger 2x18650 with EU Plug Cable features: - This product is very convenient and easy to use- Black- Material: metal and plastic- Weight: 74g- Input voltage: AC 100 -240 V 50/60 Hz- Compatible with: 18650 Li-ion- When the 18650 battery is connected to the charger, the red LED light will be displayed, and means green in full charge status- Output: DC 4.2 V, 1A- Plug: EU plug- Cable length: 38cm- The battery are not included Code A0081 Available Price €4.59
Car battery tester and charger Konnwei KW510 The Konnwei KW510 is an advanced multi-function device that uses state-of-the-art technology to allow you to easily, quickly and accurately measure the actual cold start capability, battery condition and common faults in the vehicle's starting and charging systems. The KW510 is particularly useful for workshops as it can accurately detect the problem, allowing the vehicle to be repaired quickly. Code H0586 Available Price €69.95
Solar Power Manager 5V The solar power management module with the CN3065 chip is ideal for IoT (Internet of Things) projects with renewable energy. Compared to the previous version of the module, improvements have been made to the energy management of the connected battery. Code DF025 Last items in stock Regular price €17.50 -€4.00 Price €13.50
MCP73831 - Li-Pol/Li-Ion single cell 1S 3.7V USB charger - Adafruit 1304 Charger for 1-cell lithium-polymer batteries with a nominal voltage of 3.7 V and lithium-ion batteries. The chip is powered via a USB plug, which can be connected directly to a computer socket or a power supply. Code AD002 Backorder Price €9.99
Charger 2x18650 with EU Plug Cable Charger 2x18650 with EU Plug Cable features: - This product is very convenient and easy to use- Black- Material: metal and plastic- Weight: 74g- Input voltage: AC 100 -240 V 50/60 Hz- Compatible with: 18650 Li-ion- When the 18650 battery is connected to the charger, the red LED light will be displayed, and means green in full charge status- Output: DC 4.2 V, 650mA- Plug: EU plug- The battery are not included Code A0082 Available Price €3.50