Resistor 10K Ohm 5% 0,25W 1/4W features:
-10K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Resistor 1K Ohm 5% 0,25W 1/4W features:
-1K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Resistor 220 Ohm 5% 0,25W 1/4W features:
-220 Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

LED Diode Assortment Kit 30 pcs 5mm red, green, yellow features:
- Lens color: red, green, yellow - diffuse
- Size: 5mm
- Operating current: 20mA
- Voltage (red) 1,8V-2,3V
- Voltage (green) 3,2V-3,4V
- Voltage (yellow) 1,8V-2,3V
- Anode (A): Positive (long leg): 28mm
- Catode (K): Negative (short leg): 25mm
- Operating temperature: -25ºC/80ºC
- Welding temperature: +260ºC
- Quantity: 30 units
*10x red
*10x green
*10x yellow

Resistor 200R Ohm 5% 0,25W 1/4W features:
-200R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

LED Diode Assortment Kit 40x Red Green Yellow Blue features:
  
- Lens color: Red, green, yellow, blue -difused
- Size: 5 mm
- Operating current: 20mA
- Voltage (red) 1.8V-2.3V
- Voltage (green) 3.2V-3.4V
- Voltage (yellow) 1.8V-2.3V
- Voltage (blue) 3.2V-3.4V
- Anode (A): Positive (long leg): 28mm
- Cathode (K): Negative (shorter leg): 25 mm
- Operating temperature: -25ºC/80ºC
- Welding temperature: + 260ºC
- Quantity: 40 units
      - 10x red
      - 10x green
      - 10x yellow
      - 10x blue

It is not possible to reverse the polarity by mistake.
JST PHR-2 Female 2 PIN 2mm features:
Manufacturer JST Connector series: PH Connector: plug Connector class: female Type of connector: conduit-board Raster of contactors: 2mm Number of pins: 2 Mechanical mounting: for conduit Voltage Working: 100V Working current: 2A Working temperature: -25 ... 85 ° C Connection version: contactless technical data sheet PH series

Resistor 1K Ohm 5% 0,25W 1/4W features:
-1 unit - 1K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.
Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features:
- Model: GL5516
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 90mW.
- Resistance with light (10lux): 5-10KΩ
- Resistance with darkness (0lux): 0.5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Ceramic Capacitor 100nF (0,1uF) 50v 104 PCB PIC Arduino features:

Orders only in multiples of 20 units
-Type: Ceramic Y5V
-Tolerance: +80/-20%
-Dimensions: diameter 9.5mm, pitch 5.08mm

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle.
HC-SR04 Ultrasonic Sensor Distance Measuring Module features:
- Supply voltage: 5V (4.5V- 6V)
- Consumption: 30 mA typical, (35 mA max)
- Interface: VCC , GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED indicator of measurement in progress
- Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm
- Quantity: 1 unit
Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry:
Automatic robot operation with obstacle detection />

Resistor 10K Ohm 5% 0,25W 1/4W features:
-1 unit - 10K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Resistor 330 Ohm 5% 0,25W 1/4W features:
-330 Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

It can be used to work with AVR, ARM, PIC microcontrollers, Arduino modules and to work with self-designed prototypes. Arduino Protoboard Breadboard 400 points features:
-400 Connections
-Linkable with other Plates
-Base with adhesive to attach it to the work surface
-Measures 82x55x8 mm

Resistors 100R Ohm 5% 0,25W 1/4W features:
- 100R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

3A DC Converter 1,25-32V Adjustable LM2596 Step Down Module features:

- Based on the LM2596S-ADJ regulator
- Rectification: Asynchronous
- Output Voltage: 1.25v - 32v DC (adjustable)
- Voltage of Input: 3.2v - 35v DC
- Max Output Current: 3A (with heat sink)
- Ripple at output voltage: 30mV
- Frequency: 150KHz
- Max Conversion Efficiency: 92%
- Load Regulation: ± 0.5%
- Voltage Regulation: ± 2.5%
- Operating Temperature: -40ºC to + 85ºC
- Measurements 43x 21x 14 mm

Product Category: Bipolar Transistor, NPN.
BC547B NPN 50V 100mA transistor 0.1A TO-92 features:

- Package / Case: TO-92
- Quantity: 25 units
- Collector-base voltage VCBO: 50V
- Collector-emitter voltage VCEO: 45V
- VEBO emitter-base voltage: 6V
- Continuous collector current: 100mA
- DC MAX collector current: 200mA
- Maximum power dissipation: 500mW

Resistor 4,7K Ohm 5% 0,25W 1/4W features:
- 4.7K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

5x Push Switch Button B3F Omron Blue Key 12mm features:

- 5x Push Buttons B3F Omron Key
- Maximum current: 50 mA
- Tension DC: 24V
- Operating force: 1.27N
- Switch terminals: weldable
- Contact: SPST-NO
- Contact resistance: 100M Ohm
- Type of action: Superficial
- Measures: 12x12x7.3mm

USB Cable for Arduino Type A-B features:
- Length: 50cm
- Color: Blue

Resistor 100K Ohm 5% 0,25W 1/4W features:
 100K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Resistor 330 Ohm 5% 0,25W 1/4W features:
-1 unit - 330 Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Photoresistor is a resistor whose resistance decreases with increasing intensity of light
that affects her 10x Photoresistor GL5528 LDR features:
- Model: GL5528
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 10-20KΩ
- Resistance with darkness (0lux): 1MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC
- 10k - 20k Arduino PiC 5mm
- Quantity: 10 units

Ceramic Capacitor 10nF 50v 103 PCB PIC Arduino 0.01uF features:

Orders only in multiples of 20 units
-Type: Ceramic Y5V
-Tolerance: +/-20%
-Dimensions: diameter 6mm, pitch 5.08mm

It consists of a 16-character, 2-row display.
The display is compatible with the HD44780 controller.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32. 16x2 1602 LCD display HD44780 Backlit Blue background features:
- LCD screen , 16 characters and 2 lines
- 5V power supply
- HD44780 compatible controller
- Backlit blue background, white letters
- Include an adjustable contrast pin
- Dimensions (mm): 80 x 36 x 12

Resistor 2,2K Ohm 5% 0,25W 1/4W features:
-2.2K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Tower Pro Micro Servo 9g SG90 features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

10x Male-Male Cables 20cm Jumpers Dupont 2,54 features:
-Length: 20cm
-Quantity: 10 cables
-Connectors have male header contacts at either end
-Compatible with female connectors 2,54mm
-High quality and good working conditions
-Easy to install and use

Resistors 470R Ohm 5% 0,25W 1/4W features:
- 470R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Prototype Board MB-102 Protoboard 830 points Arduino features:
- 830 Connections
- Linkable with other boards
- Base with adhesive to attach it to the work surface
- Measures 165x 55x8mm

Lot of 65 Male-Male jumper cables. Characteristic: -No soldering required
-You can easily modify or revise the circuits
-Quantity: 65 cables of different lengths and colors
-Cable lengths: 120mm, 150mm, 200mm, 240mm

28BYJ-48 Stepper Motor 12V + Driver Board ULN2003 features:
- Stepper motor 28BYJ-48 + ULN2003 controller
- The 28BYJ-48 has everything you need to start using motors step by step in your project
- A stepper motor converts digital impulses into small steps of movement in one direction
- The motor also comes with a ULN2003 motor controller card
- Can control two DC motors or a motor with bipolar steps with a maximum amperage of up to 500 mA
- Equipped with state indicator LEDs A, B, C, D
- Engine model: 28BYJ-48
- Phasing Engine: 4
- Operating voltage: 12V DC
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 Ohm
- Angle per step: 5,625º
- Steps per round: 64

10x Female-Male Cables 20cm Jumpers Dupont features:
-Length: 20cm
-Quantity: 10 cables
-Connectors have male and female header contacts at either end
-Compatible with male and female connectors 2,54mm
-High quality and good working conditions
-Easy to install and use

LED 5mm RGB 4 Pins cathode commun with clear water lens.

Characteristic:
- Lens color: white,
- Diameter of the bulb: 5 mm,
- Operating current: 20mA,
- Voltage: 2.0V-2.2V,
- Wavelength: 588-590 nm,
- Anode (A): Positive (long leg): 19mm,
- Cathode (K): Negative (shorter leg): 17 mm,
- Operating temperature: -25ºC / 80ºC,
- Welding temperature: + 260ºC,
- Quantity: 10 units.

It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision.
The ideal obstacle detection detector for the installation of smart robots.
TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object.
The working wavelength is 950nm.
The transmitter is infrared LED and the phototransistor receiver.
By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected).
The sensor allows the detection of an object at a distance of up to 12 mm.

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.
DS18B20 Submersible Probe Sensor Temperature features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Red Vcc
      - Yellow digital output
- Inocidable steel
- Cable length: 1m

10x Electrolytic Capacitor 100 uF 25V 105ºC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 100uF
-Maximum tension: 25V
-Maximum temperature: 105º C
-Dimensions: 6x11mm
-Quantity: 10 units

Low Signal High Speed ​​Switching.
These diodes are widely used to multiplex signals, such as buttons or digital inputs Characteristic:
- Reverse voltage: 100V,
- Forward voltage drop: 1V to 10mA,
- Forward direct current: 200mA,
- Maximum overvoltage current: 4A,
- Dissipated power: 500mW,
- Recovery time: 4ns,
- Configuration: Simple,
- Package: DO-35,
- Quantity: 30 units .

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

1N4007 Rectifier Diodes 1A 1000V DO-41 features:
- Standard rectifier diode
- Configuration: Simple
- Reverse voltage: 1000V
- Direct voltage drop: 1V
- Direct direct current: 1A
- Maximum overvoltage current: 30A
- Encapsulated: DO-41
- Operational tension: -65ºC to + 125ºC

40x Male to male cables 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont male connectors on both ends
- Compatible with 2.54mm female connectors
- High quality and good working condition
- Easy to install and use

Characteristic:
-10k OHM kΩ - linear potentiometer 10k Arduino
-Tolerance: +/- 20%
- Power: 0.125W

Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects.
Buzzer 5V Active Buzzer 4 to 7V DC features:

- Input voltage: 4V to 7V
- Diameter: 12mm
- Height: 9.5mm
- Spacing Pins: 7.6mm
- Maximum Current:

Push button 6x6x4mm features:
-Touch Push Tact Switch mini electronic Arduino push button
-Measures: 6x6x4.3mm

Ideal to power your Arduino board through the power input.
Adapter Battery 9V 6F22 Jack Connector DC features:
- Cable 7cm long
- Battery connector 9V, 6F22
- Male connector DC 5.5 / 2.5

40x Female Male 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

Electronic Antistatic Wrist Bracelet ESD Blue features:
- Electronic Antistatic Bracelet, blue color
- Protection against electrostatic charges
- Adjustable bracelet with crocodile clip connector
- Material: The conductive elastic band is made of nylon and woven in stainless steel
- Extensible length up to 180 centimeters
- Weight: 25 gr.
- Quantity: 1 loose unit in plastic bag

Resistor 150R Ohm 5% 0,25W 1/4W features:
-150R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Characteristic: -Length: 20cm
-Quantity: 40 cables
-Mono Dupont connectors on both ends
-Compatible with 2.54mm female connectors
-High quality and good working condition
-Easy to install and use

Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:
- Model: GL5539
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 50-100KΩ
- Resistance with darkness (0lux): 5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

40x Cables Female-Male 20cm features:
-Length: 20cm
-Quantity: 40 cables
-Connectors have male and female header contacts at either end
-Compatible with female connectors 2,54mm
-High quality and good working conditions
-Easy to install and use

Tower Pro Micro Servo 9g SG90 360 degree features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

DC Gear Motor 6V 148 Arduino features:
- Voltage: 3 to 6Vdc
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Reduction: 1:48

LCD display consists of a 16-character, 2-rows.
The display is compatible with the HD44780 controller
Ideal for projects with Arduino
You can use it with PIC, AVR, STM32 and many more controllers.

Push button 6x6x4mm features:
-Touch Push Tact Switch mini electronic Arduino push button
-Measures: 6x6x45mm
-Quantity: 1 unit

5x Push Switch Button B3F Omron Red Key 12mm features:

- 5x Push Buttons B3F Omron Key
- Maximum current: 50 mA
- Tension DC: 24V
- Operating force: 1.27N
- Switch terminals: weldable
- Contact: SPST-NO
- Contact resistance: 100M Ohm
- Type of action: Superficial
- Measures: 12x12x7.3mm

15x Electrolytic Capacitor 4,7uF 50V 105ºC PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 4.7uF
-Maximum tension: 50V
-Maximum temperature: 105º C
-Dimensions: 5x11mm
-Quantity: 15 units