Mobile
Perfect kit to learn programming in the middle of Arduino the basic of electronics It allows to build various projects of various complexity, from the easiest ... to the most complicated.The elements are placed in the box to keep everything in order. Characteristic: It includes the following module references: - 1x UNO R3 Rev3 ATmega328 ATmega16U2 Development Board Arduino Module - 1x LED Display Screen Controller Blue Backlight 16x2 1602 HD44780- 1x Prototype Protoboard MB-102 830 points Arduino- 1x ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Proto V5.0- 1x 74HC595 74595 SN74HC595N 8-Bit Shift Register DIP-16- 1x LM35 Temperature Sensor LM35DZ TO92- 2x SW-520D Vibration Tilt Sensor
Perfect kit to learn programming in the middle of Arduino the basic of electronics It allows to build various projects of various complexity, from the easiest ... to the most complicated.The elements are placed in the box to keep everything in order. Characteristic: It includes the following module references: - 1x UNO R3 Rev3 ATmega328 ATmega16U2 Development Board Arduino Module - 1x LED Display Screen Controller Blue Backlight 16x2 1602 HD44780- 1x Prototype Protoboard MB-102 830 points Arduino- 1x ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino Proto V5.0- 1x 74HC595 74595 SN74HC595N 8-Bit Shift Register DIP-16- 1x LM35 Temperature Sensor LM35DZ TO92- 2x SW-520D Vibration Tilt Sensor- 1x Fire sensor - 1x Thermistor NTC 10.0K 5% - 3x Photoresistor GL5516 LDR- 5x Push Switch Button B3F Omron Yellow Key- 1x Potentiometer B10K Linear- 1x 2 Axis Joystick Module XY PS2- 1x Water Level Sensor Module AVR ST- 1x DS1302 Real Time Clock RTC Module AVR ARM PIC- 1x RFID Module with Card and Pendant- 1x DHT11 Temperature and Humidity Sensor Module- 1x Sound Detection Sensor Module- 1x Full Color LED Module RGB Bulb KY-016- 1x LED Display 1-Digit 7-Segment Red Common Cathode- 1x LED Display 4-Digit 7-Segment Red Common Cathode - 1x LED Display Screen Board Matrix 8x8 Red- 1x Buzzer Alarm 5V 4 to 7V DC- 1x Passive Buzzer 5V- 1x Infrared Wireless Remote Control IFR NEC HX1838- 1x Infrared Receiver VS 1838 38kHz- 1x 4x4 High Quality Keyboard Matrix Push Buttons 16 Touch Keys- 1x LED Diode Assortment Kit 30 pcs 5mm red, green, yellow- Resistors: - 10x Resistors 200R Ohm 5% 0,25W 1/4W - 10x Resistors 1K Ohm 5% 0,25W 1/4W - 10x Resistors 10K Ohm 5% 0,25W 1/4W- 1x Tower Pro Micro Servo 9g SG90- 1x Relay module 5V 1 channel- 1x 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat- 1x Adapter Battery 9V 6F22 Jack Connector DC- 1x USB Cable for Arduino UNO Type A-B- 10x Male-FeMale Cables 20cm Jumpers Dupont 2,54- 65x Cable Jumper Male The references are packaged inside a transparent plastic case. Helpful Links: Install the IDE Arduino development interface - Download the Arduino program interfaceThe usual Arduino libraries User's manual for common modules of the kits Write your first program in the Arduino IDE
Data sheet
- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328
Prototype Board MB-102 Protoboard 830 points Arduino features: - 830 Connections - Linkable with other boards - Base with adhesive to attach it to the work surface - Measures 165x 55x8mm
ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 features: - To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Uno R3, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip- The seamless mini breadboard has 170 connection points.- You can stick on the shield with its self-adhesive back.
With this multiplexer circuit we will be able to get 8 more digital outputs for arduino losing only 3 of them. Characteristic: - Logic Circuit - Type: DIP-16 - Logic Circuit - Type: Displacement Register - Displacement Register - Function: Series to Parallel, Series to Series - Supply Voltage Max .: 6V - Supply Voltage Min .: 2V - IC - Output Type: Tri-State Quantity: 4 units.
LM35 Temperature Sensor LM35DZ TO92 features:- The output is linear and each degree Celsius equals 10 mV- Power supply from 4 to 30 Vdc- Connection through analog input- Temperature range from 0ºC to 100ºC- Linearity +10 mV / ºC- Quantity: 1 unit
Resistors 100R Ohm 5% 0,25W 1/4W features:- 100R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm
Led infrared sensor.Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm features: - Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino.
NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 10.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm
10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC
- Maximum current: 50 mA- Tension DC: 24V- Operating force: 1.27N- Switch terminals: weldable- Contact: SPST-NO- Contact resistance: 100M Ohm- Type of action: Superficial- Measures: 12x12x7.3mm
Characteristic: -10k OHM kΩ - linear potentiometer 10k Arduino -Tolerance: +/- 20% - Power: 0.125W
Ideal for your arduino projects, but can also be used with other microcontrollers. Double Joystick Module 2 Axis XY PS2 features: - Two axes (XY) - Return to the center - Central push button - Connections: + 5Vcc / GND / VRx / VRy / SW - Dimensions: 4 x 2.6 x 3.2cm
Easily convert water level to analog signal The analog output signal can be read directly on the Arduino board Characteristic: - Operating voltage: 3.3V -5 V - Consumption: less than 20 mA - Sensor type: Analog - Operating temperature: 10º C -30º C - Detection area: 40 mm x 16 mm - Dimensions: 60 mm x 20 mm
Ideal for projects with ARDUINO you can use it with PIC, AVR, STM32.Provides seconds, minutes, time and date, calendar up to the year 2100.DS1302 Real Time Clock RTC Module AVR ARM PIC features:- Chip: DS1302- Power supply: 2V-5V- Operating current: <2mA- Dimensions: 44 x23 x 8mm- Battery not included in this sale- Connect the RTC to your ArduinoVCC -> Arduino + 3.3VGND -> Arduino GndCLK -> (SCLK_PIN)DAT -> (IO_PIN)RST -> (CE_PIN)
It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95%
The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables
Sound detection module for Arduino projects, smart cars.Sound Detection Sensor Module features:- Adjustable High Sensitivity Acoustic Sensor- Chip LM393- Red LED indicator integrated- Frequency range between 30 and 15000 Hz- Power 4 ~ 6V- Measures 32x16x10mm
LED Display 1-Digit 7-Segment Red Common Cathode features:- Supply voltage of the segments: 3 VDC- LED color of the segments: red- Digit length: 14.2mm- Digit width: 8.1mm- Pin numbers: 10- Diameter of pins: 0.51mm- Step between pins: 2.54mm- Consumption current per segment: 30mA- Maximum admissible current per segment: 70mA- Direct current by segment (pulse operation): 30mA- Number of digits: 1- Segment numbers by digit: 7- Operating temperature: -25 ° C - + 85 ° C- Storage temperature: -30 ° C - + 85 ° C- Screen with common cathode connection- Screen size: 12.6x19x8 mm- This product is a 1 digit screen composed of 7 red LED segments with excellent brightness and features:.
LED Display 4-Digit 7-Segment Red Common Cathode features:- Supply voltage of the segments: 3 VDC- LED color of the segments: red- Digit length: 14.2mm- Digit width: 8.1mm- Pin numbers: 12- Diameter of pins: 0.51mm- Step between pins: 2.54mm- Consumption current per segment: 30mA- Maximum admissible current per segment: 70mA- Direct current by segment (pulse operation): 30mA- Number of digits: 4- Segment numbers by digit: 7- Operating temperature: -25 ° C - + 85 ° C- Storage temperature: -30 ° C - + 85 ° C- Screen with common cathode connection- Screen size: 50.3x19x8 mm- This product is a 4-digit screen composed of 7 red LED segments with excellent brightness and features:.
LED Display Screen Board Matrix 8x8 Common Cathode/Columns Common Anode Red Dots features:- Supply voltage of the LED points: 1.8-2.4 VDC- LED color of the dots: red- Pin numbers: 16- Diameter of pins: 0.51mm- Step between pins: 2.54mm- Consumption current per segment: 30mA- Maximum admissible current per segment: 120mA- Power consumed per segment: 80mW- Segment numbers (points): 64- Diameter of a point: 3mm- Operating temperature: -35 ° C - + 85 ° C- Storage temperature: -35 ° C - + 85 ° C- Screen with common cathode connection for the rows and common anode for the columns- Screen size: 32x32x8 mm
Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects. Buzzer 5V Active Buzzer 4 to 7V DC features: - Input voltage: 4V to 7V - Diameter: 12mm - Height: 9.5mm - Spacing Pins: 7.6mm - Maximum Current:
The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features: - Input voltage: 3V to 12V - Diameter: 12mm - Height: 7.5mm - Pin spacing: 6.5mm - Impedance: 16 Ohm - Working frequency: 2 to 5 KHz - Quantity: 1 unit
Arduino Raspberry Remote Control HX1838 Infrared Emitter NEC IR Remote Control Infrared emitter HX1838 features: - 21 keys - Measurements 85x 40x 5mm - Includes battery Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Send / Receive information via IR - Wiring of the IR Remote control + Infrared IR Receiver VS1838 with UNO module - Lighting a red 3mm LED by Infrared Realization of a manageable Infrared robot - Wiring the IR Distance remote control + Infrared IR Receiver VS1838 with the UNO module - Fix the IR Distance remote control + VS1838 Infrared IR Receiver in a Mini 2WD DIY Car Robot Kit
Ideal for projects with ARDUINO, PIC, AVR, Raspberry The infrared receiver receives the signal of 38kHz for remote control
LED Diode Assortment Kit 30 pcs 5mm red, green, yellow features:- Lens color: red, green, yellow - diffuse- Size: 5mm- Operating current: 20mA- Voltage (red) 1,8V-2,3V- Voltage (green) 3,2V-3,4V- Voltage (yellow) 1,8V-2,3V- Anode (A): Positive (long leg): 28mm- Catode (K): Negative (short leg): 25mm - Operating temperature: -25ºC/80ºC- Welding temperature: +260ºC - Quantity: 30 units*10x red*10x green*10x yellow
Resistor 200R Ohm 5% 0,25W 1/4W features:-200R Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm
Resistor 1K Ohm 5% 0,25W 1/4W features:-1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm
Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm
Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm
1 Channel 5V Relay Module. This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). Relay Module 1 Channel 5V 10A features: - Channel: 1 - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - LED indicator - Dimensions: 30x 54mm
Ideal to power your Arduino board through the power input.Adapter Battery 9V 6F22 Jack Connector DC features:- Cable 7cm long- Battery connector 9V, 6F22- Male connector DC 5.5 / 2.5
USB Cable for Arduino Type A-B features: - Length: 50cm- Color: Blue
10x Female-Male Cables 20cm Jumpers Dupont features: -Length: 20cm-Quantity: 10 cables-Connectors have male and female header contacts at either end-Compatible with male and female connectors 2,54mm-High quality and good working conditions-Easy to install and use
Lot of 65 Male-Male jumper cables. Characteristic: -No soldering required -You can easily modify or revise the circuits -Quantity: 65 cables of different lengths and colors -Cable lengths: 120mm, 150mm, 200mm, 240mm
LCD display consists of a 16-character, 2-rows. The display is compatible with the HD44780 controller Ideal for projects with Arduino You can use it with PIC, AVR, STM32 and many more controllers.
The 28BYJ-48 has everything you need to start using stepper motors in your projectA stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller cardCan control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mAEquipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features: - Engine model: 28BYJ-48- Phases engine: 4- Operating voltage: 5V- Frequency: 100 Hz- Operating current: 200mA- Max Power: 20W- Winding resistance: 70 ohm- Angle per step: 5,625º- Steps per round: 64- Torque: 0.3 Kgr / cm- Speed: 1900 rpm
47,00 tax excl.
Backorder