Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €8.95
2x Insulation Tapes PVC Green 10m x 15mm x 0.13mm 2x Insulation Tapes PVC Green 10m x 15mm x 0.13mm features:- PVC insulating tape with adhesive- Thickness of 0.13 mm- Measures 10m x 15mm- Quantity: 2 units- Heat resistance: 80°C Code H0035 Available Price €0.99
Power Supply 12V 33A 400W Characteristic: - Supply voltage: 110 / 230V AC - Output voltage: 12V DC / + 10% -15% / 150mVpp - Output amperage: 33A - Power at 12V: 400W - Dimensions: 260mm x 105mm x 65mm Code A0099 Available Price €29.58
40x Female-Female Cable 20cm 40x Female-Female Cable 20cm features: -Length: 20cm -Quantity: 40 wires -Dupont female connectors on both ends -Compatible with 2.54mm male connectors -High quality and good working condition -Easy to install and use Code K0004 Available Price €2.49
12V On/Off LED Pushbutton Red 16mm N/A NO Latching push-button 12V normally open- For panel N / A NO 2A 36V Stainless Steel on / off- Type of operation: On / Off- Contact switch: 1 NA (normally open)- Max Switch Classification: 2A / 12VDC- Body material: Stainless steel- Button Material: Stainless steel- Protection Classification: IP67 / IK08- Operating temperature: -20C + 55C- Color: Red Code K0194 Available Regular price €5.89 -25% Price €4.42
Laminated Copper Clad Prototype PCB Circuit Board 10x15cm Laminated Copper Clad Prototype PCB Circuit Board 10x15cm, 0.35um double side. Code PB014 Available Price €2.15
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
Desoledring Pump with Heater 40W 220V Desoledring Pump with Heater 40W 220V features: - It allows to remove tin- Easy to use with one hand.- Desoldering pump with heater- Consumption: 40W- CE Certificate- Quantity: 1 unit Code H0098 Available Price €9.49
Third hand support for cable soldering Third hand stand for easy soldering of wires with a diameter from 1 to 5mm. Number of holes 5. Code MX0001 ✗ Out-of-Stock Regular price €3.79 -€0.90 Price €2.89
60/40 Tin Lead Solder Wire Soldering Flux Sn60/Pb40 2.5% 0.7mm 50g 60/40 Tin Lead Solder Wire Soldering Flux Sn60/Pb40 2.5% 0.7mm 50g features:- 50gr. 0.7mm diameter welding wire. 60% tin and 40% lead.- Fusing temperature 183°C/190°C.- Alloy: Sn60 Pb40- Flux 2.5%- Quantity: 1 unit Code Q0002 ✗ Out-of-Stock Price €3.95
Vacuum Pump Components SMD Suction Cup Suction Vacuum Pump Components SMD Suction Cup Suction features: - An economical option for suction for handling SMD components- Includes 3 suckers of different sizes Code H0118 Available Price €2.73
Flux Gel RMA 100cm3 Flux gel 100cm3 of RMA class, intended for SMT assembly and repairs. Flux gel can be applied through a sieve, pattern or from a syringe. Activators utilized in flux manufacturing process enable to leave its remnants after soldering on the package (as far as the process does not include washing phases). Code Q0116 ✗ Out-of-Stock Price €19.89
Flux BORAX 500g Flux BORAX Unblocker features: Flux for soldering and welding with brazing solders. Dissolves metal oxides and facilitates bonding of solder with soldered material. Borax occurs as fine crystalline without fluorides. Code Q0066 ✗ Out-of-Stock Price €3.95
Flux Solid Resin Rosin 20g Flux rosin, solid resin, neutral pH for correct electronic soldering - They do not cause corrosion of non-ferrous metals - Does not cause short circuits Melts with temperature, spreads over the area to be welded and penetrates into the most difficult corners cleans and prepares the surfaces and components to be welded, and facilitates adhesion and tin fluidity, improving soldering in electronics jobs. Use a toothpick for the application. Do not apply excessively. Safety: - Use in ventilated spaces. Do not inhale the fumes that are given off by welding. - Keep the bottle tightly closed and out of the reach of children. - Do not ingest. Non-toxic - Rarely irritating to skin contact Code Q0010 Available Price €1.69
3x Long Life Soldering Iron Tips Replacement Ø 3.8mm 3x Long Life Soldering Iron Tips Replacement Ø 3.8mm features: - Power: 40W- Rod ø 3.80 mm- Length 70 mm- Long duration tip Code H0015 ✗ Out-of-Stock Price €2.99
Flux Welding Paste 20g Characteristic: - Solder paste according to DIN EN 29454-1 1.1.2.C. - Flux paste based on activity rosin medium. - Easy to weld: copper, silver, zinc and nickel plated. Flux residues after soldering do not cause corrosion of non-ferrous metals and can remain in the joints . Operating temperature up to 350 C. Code Q0025 Available Price €1.89
Varnish Flux LT-4 - The product protects PCB plates, allows for easier welding- The product protects the printed circuit boards against oxidation and corrosion during storage.- This allows a faster welding and avoids the "cold welding".- The application method allows easy distribution of the product on the plates.- Can be used during production, repair, maintenance and service.Flux Varnish LT-4 Plate Protector features:- Shape: Spray- Capacity: 100ml- Rosin RMA- Meets the requirements of DIN 8511, F-SW-31, PN EN 29454 1.1.1.A.Application:- PCB protection against oxidation,- Applied in the production of printed circuit boards immediately after engraving, Code Q0070 Available Price €5.95
Desoledring Pump with Heater 40W 220V Desoledring Pump with Heater 40W 220V features: - It allows to remove tin- Easy to use with one hand.- Desoldering pump with heater- Consumption: 40W- CE Certificate- Quantity: 1 unit Code H0098 Available Price €9.49
Third hand support for cable soldering Third hand stand for easy soldering of wires with a diameter from 1 to 5mm. Number of holes 5. Code MX0001 ✗ Out-of-Stock Regular price €3.79 -€0.90 Price €2.89
60/40 Tin Lead Solder Wire Soldering Flux Sn60/Pb40 2.5% 0.7mm 50g 60/40 Tin Lead Solder Wire Soldering Flux Sn60/Pb40 2.5% 0.7mm 50g features:- 50gr. 0.7mm diameter welding wire. 60% tin and 40% lead.- Fusing temperature 183°C/190°C.- Alloy: Sn60 Pb40- Flux 2.5%- Quantity: 1 unit Code Q0002 ✗ Out-of-Stock Price €3.95
Vacuum Pump Components SMD Suction Cup Suction Vacuum Pump Components SMD Suction Cup Suction features: - An economical option for suction for handling SMD components- Includes 3 suckers of different sizes Code H0118 Available Price €2.73
Flux Gel RMA 100cm3 Flux gel 100cm3 of RMA class, intended for SMT assembly and repairs. Flux gel can be applied through a sieve, pattern or from a syringe. Activators utilized in flux manufacturing process enable to leave its remnants after soldering on the package (as far as the process does not include washing phases). Code Q0116 ✗ Out-of-Stock Price €19.89
Flux BORAX 500g Flux BORAX Unblocker features: Flux for soldering and welding with brazing solders. Dissolves metal oxides and facilitates bonding of solder with soldered material. Borax occurs as fine crystalline without fluorides. Code Q0066 ✗ Out-of-Stock Price €3.95
Flux Solid Resin Rosin 20g Flux rosin, solid resin, neutral pH for correct electronic soldering - They do not cause corrosion of non-ferrous metals - Does not cause short circuits Melts with temperature, spreads over the area to be welded and penetrates into the most difficult corners cleans and prepares the surfaces and components to be welded, and facilitates adhesion and tin fluidity, improving soldering in electronics jobs. Use a toothpick for the application. Do not apply excessively. Safety: - Use in ventilated spaces. Do not inhale the fumes that are given off by welding. - Keep the bottle tightly closed and out of the reach of children. - Do not ingest. Non-toxic - Rarely irritating to skin contact Code Q0010 Available Price €1.69
3x Long Life Soldering Iron Tips Replacement Ø 3.8mm 3x Long Life Soldering Iron Tips Replacement Ø 3.8mm features: - Power: 40W- Rod ø 3.80 mm- Length 70 mm- Long duration tip Code H0015 ✗ Out-of-Stock Price €2.99
Flux Welding Paste 20g Characteristic: - Solder paste according to DIN EN 29454-1 1.1.2.C. - Flux paste based on activity rosin medium. - Easy to weld: copper, silver, zinc and nickel plated. Flux residues after soldering do not cause corrosion of non-ferrous metals and can remain in the joints . Operating temperature up to 350 C. Code Q0025 Available Price €1.89
Varnish Flux LT-4 - The product protects PCB plates, allows for easier welding- The product protects the printed circuit boards against oxidation and corrosion during storage.- This allows a faster welding and avoids the "cold welding".- The application method allows easy distribution of the product on the plates.- Can be used during production, repair, maintenance and service.Flux Varnish LT-4 Plate Protector features:- Shape: Spray- Capacity: 100ml- Rosin RMA- Meets the requirements of DIN 8511, F-SW-31, PN EN 29454 1.1.1.A.Application:- PCB protection against oxidation,- Applied in the production of printed circuit boards immediately after engraving, Code Q0070 Available Price €5.95